Home Blog Page 5486

Crutchlow Grabs British Superbike Pole Position At Oulton Park

0

Cal Crutchlow powered his HM Plant Honda to pole start for the seventh round of the Bennetts British Superbike Championship at Oulton Park and promised to convert his pace into a winning double to steel his chances of reeling in Shane Byrne in the title stakes. The Coventry rider enjoys riding the Cheshire circuit, having taken pole in the earlier visit there back in May then in the races he had mixed fortunes with a sixth place and then a tumble but this time around Crutchlow is determined to show what might have been. “I’m looking forward to getting back out there in the races and am keen to make amends for what happened here earlier on believe me, I will be giving it everything out there,” said Crutchlow after his success in the Swan Combi 50 Roll for Pole. His pole setting lap came in 1m 36.298secs, an average speed of 100.63mph, and it might have been better. “I was baulked a bit on one lap and it was very windy out there, a bit dodgy in places, so it might have been faster, but it is good to be back on top. Now I hope to turn this into two race wins I’ve got to go for it here, it’s my favourite circuit so really there is nothing else but achieving that.” Crutchlow, one of only three riders to have beaten the dominant Byrne so far this term, starts the races with a 97 points deficit on the Airwaves Ducati rider in the standings. There is only 0.292 seconds between them at the top of the leaderboard, with Byrne confident that he can repeat his winning double of that first visit here. Tom Sykes joined them at the front of the grid, powering his Rizla Suzuki to a 1m 36.591secs lap of this 2.692 mile circuit, just 0.001secs down on Byrne but a quarter of a second up on Leon Haslam, riding the second HM Plant bike, who completed the front row. Karl Harris, the Rob Mac Racing Yamaha, who had set the pace through Friday’s free practice ran fifth best, though within half a second of Crutchlow, to nudge Simon Andrews, aboard the Lloyds British Jentin Yamaha back a place on a second row that also included Mallory Park race winner Michael Rutter on the North West 200 Ducati and James Ellison on the Hydrex Bike Animal Honda. Tristan Palmer continued his strong performances, running ninth fastest on the Tena for Men Honda ahead of Billy McConnell, the MSS Discovery Kawasaki rider who escaped injury in a tumble. Scott Smart, riding Hawk Kawasaki, joined them on the third row together with Gary Mason, the fastest of the Daily Star Cup contenders, aboard the Quay Garage Honda. Cup leader John Laverty ran second in class on the Buildbase NW200 Ducati ahead of Riders Honda’s Martin Jessopp and Chris Burns aboard the STP MV Agusta. Leading qualifying times: 1. Cal Crutchlow (HM Plant Honda) 1:36.298s 2. Shane Byrne (Airwaves Ducati) +0.292s 3. Tom Sykes (Rizla Suzuki) +0.292s 4. Leon Haslam (HM Plant Honda) +0.523s 5. Karl Harris (Rob Mac Racing Yamaha) +0.533s 6. Simon Andrews (Lloyds British Yamaha) +0.807s 7. Michael Rutter (North West 200 Ducati) +1.073s 8. James Ellison (Hydrex Bike Animal Honda) +1.260s 9. Tristan Palmer (TENA for Men Honda) +1.502s 10. Billy McConnell (MSS Discovery Kawasaki) +1.542s More, from a press release issued by Team Suzuki News Service: Rizla Suzuki’s Tom Sykes took a hard-fought third place at Oulton Park for round seven of the Bennetts British Superbike Championship while his team-mate Atsushi Watanabe came home in 13th position. The 50-minute qualifying session started off in damp conditions but the 2.69-mile Cheshire circuit dried rapidly. Sykes was always in contention for pole position and led the time-sheets for much of the session, showing he has real race-winning pace. Watanabe used his previous experience at Oulton Park to maintain his top 15 placing and will be aiming for a top-10 finish when the racing starts in anger. Race one will take place at 1315 on Sunday and race two at 1630. Tom Sykes: “I think I could have been a little further up if I hadn’t been caught up in traffic at the end of the session but third place and the front row of the grid is fine as I know I can get away well. During free practice we worked our way through a number of wet settings and we have made some progress getting the bike nicely balanced for racing in the rain if it comes tomorrow. “In the dry there is still a bit of work to be done as the front end is feeling a little vague at a couple of corners and I want the bike to be doing the work rather than me. I can put in consistent 1min 36s which is a good race pace so I feel confident ahead of tomorrow’s races.” Atsushi Watanabe: “I am happy I have improved since last Oulton Park. My lap times are better and my feeling for the track. My Rizla Suzuki technicians worked hard on rear settings to improve how my bike feels as it had a lot of movement. I want a good finish tomorrow for me and my team.” Pete Jennings – Crew Chief: “Tom did get baulked towards the end of the session which was a shame but his race pace is good, and we have a few little changes to make ahead of race day which we will evaluate during warm-up.” Qualifying results: 1: Cal Crutchlow (Honda) 1:36.298 2: Shane Byrne (Ducati) +0.292 3: Tom Sykes (Rizla Suzuki) +0.293 4: Leon Haslam (Honda) +0.523 5: Karl Harris (Yamaha) +0.533 6: Simon Andrews (Yamaha) +0.807 7: Michael Rutter (Ducati) +1.073 8: James Ellison (Honda) +1.260 9: Tristan Palmer (Honda) +1.502 10: Billy McConnell (Kawasaki) +1.542 13: Atsushi Watanabe (Rizla Suzuki) +1.754 More, from a press release issued by GSE Racing/Airwaves Ducati: BYRNE ON THE FRONT ROW FOR AIRWAVES DUCATI Airwaves Ducati rider Shane Byrne will start on the front row for round 7 of the British Superbike Championship. Shane achieved the 2nd fastest time in qualifying at Oulton Park today. Team mate Leon Camier will start from row 8. After a wet practice session in the morning, which both Airwaves Ducati riders decided to sit out, qualifying was to remain dry for the full 50 minutes. Shane pushed hard throughout the session and his fastest lap time of 1:36.590 came on lap 22 of 24. Continuing his run of starting on the front row for every race so far this season, Shane said: “I’m really happy to have secured a front row start for Airwaves Ducati. I was stuck behind traffic on my fastest lap and my final corner was sacrificed by not being able to take my normal line. I had one last chance to try and grab pole but the wind just caught me out on the first corner. But I can’t complain with second. If warm-up tomorrow morning is dry there are a few slight changes that I would like to try on the Airwaves Ducati, but if not, I’m confident that the races should bring us some good results, and importantly more championship points.” Qualifying came to a premature end for Leon when 15 minutes into the session and on his 5th lap he came off at Island bend. As he took no further part in the qualifying session, Leon was unable to better his time of 1:41.644 and so will start tomorrow’s races from 29th on the grid. Following qualifying, Airwaves Ducati Team Manager Colin Wright commented, “Leon had been doing a good job so far this weekend and he felt confident going into qualifying. The session started as planned and he was looking to get into a good rhythm but unfortunately he slipped off. Physically Leon is OK but he did take a heavy fall and he is unsure as to the reason for the crash. We will assess his condition in the morning and decide if he is fit to race.” Qualifying Result: 1. Cal Crutchlow HM Plant Honda 1:36.298 2. Shane Byrne – Airwaves Ducati 1:36.590 3. Tom Sykes Rizla Suzuki 1:36.591 4. Leon Haslam HM Plant Honda 1:36.821

Updated Again: Saturday Morning AMA Superbike Practice At Laguna Seca Cancelled Due To Fog

0

The 40-minute AMA Superbike practice session scheduled for Saturday morning at Mazda Raceway Laguna Seca has been canceled due to fog and limited visibility and will not be rescheduled, according to AMA Superbike Media Relations Manager Eric Putter.

The session was the only practice session scheduled for the AMA Superbike class Saturday and would have been their second of two on the weekend.

The AMA Superbike practice will not be rescheduled due to the FIM MotoGP World Championship schedule taking priority this weekend.

AMA Superbike is scheduled to have a 25-minute qualifying session Sunday morning, prior to a 28-lap race at 3:45 p.m. local time Sunday afternoon.

Update: Saturday’s AMA Superbike practice may be rescheduled from 5:15 to 5:45 p.m. local time, according to AMA Pro Racing’s Bill Syfan. “Our friends with FIM, Dorna and the track are working on making that time available to us,” said Syfan. “We are working it out. We polled the teams about the possibility of the 5:15 session, and they were pretty positive about it.”

“Anytime you schedule a session at 8:00 a.m. at Laguna Seca you never know what you’re going to get,” said six-time AMA Superbike Champion Mat Mladin. Mladin, who agreed that it was too foggy to ride, said the session at 5:15 p.m. Saturday could end up being more productive because it will be closer to the actual time of day of the race.

Second Update: Saturday’s AMA Superbike practice has officially been rescheduled for 5:15 to 5:45 p.m. Saturday.

Updated: Bruce Rossmeyer’s Daytona Racing On Pole Position For SunTrust MOTO-ST Race At Barber

0

Barber SunTrust MOTO-ST 500K Barber Motorsports Park Birmingham, Alabama July 19, 2008 Qualifying Results (all on Pirelli tires): 1. Bruce Rossmeyer’s Daytona Racing (Shawn Higbee/Mike Smith), Buell 1125R, SuperSport Twins, 1:32.040 2. Touring Sport Ducati 75 (Ryan Gordon/Ryan Elleby/Frank Shockley), Ducati 848, SuperSport Twins, 1:32.313 3. Aprilia USA 1/Lloyd Brothers Motorsports (Ty Howard/Mike Himmelsbach/Zac Chapman), Aprilia RSV1000, SuperSport Twins, 1:33.035 4. Aprilia USA 6/Lloyd Brothers Motorsports (Henry Wiles/Zac Chapman/Ty Howard), Aprilia RSV1000, SuperSport Twins, 1:33.354 5. CrozierMotorsports.com (Mark Crozier/Nathan Dressman), Ducati 848, SuperSport Twins, 1:33.951 6. National Precious Metals (Marco Martinez/Calvin Martinez), Ducati 848, SuperSport Twins, 1:35.145 7. Rightsforbikers.com (Justin Filice/Armando Ferrer/Rodolfo Ramirez), Ducati PS1000LE, Grand Sport Twins, 1:35.536 8. Team Hooters Aprilia (Andy Deatherage/Ben Carlson/Mike Luke), Aprilia RSV1000, SuperSport Twins, 1:35.615 9. Touring Sport Ducati 77 (Pete Friedland/Brad Phillips/Frank Shockley), Ducati PS1000LE, Grand Sport Twins, 1:36.792 10. M4 AVTEQ Racing 66 (Dane Westby/Kyle Martin/Russell Wikle), Suzuki SV650, Sport Twins, 1:36.994 More, from a press release issued by MOTO-ST: > Higbee fastest in SunTrust MOTO-ST qualifying at Barber Motorsports Park BIRMINGHAM, Ala. (July 19, 2008) Shawn Higbee earned his second consecutive SunTrust MOTO-ST Series pole position on Saturday morning, when he posted the fastest time during qualifying in advance of Sunday’s Barber 500K at Barber Motorsports Park. The Oconomowoc, Wis. racer converted his ‘Destination Daytona Pole Award’ into a Buell Motorcycle Company Super Sport Twins (SST) class victory in early June at the MOTO-ST event in Elkhart Lake, Wisconsin, and is hoping for a repeat performance on Sunday at the scenic Barber circuit, located near Birmingham, Ala. Higbee’s No. 8 Bruce Rossmeyer’s Daytona Racing Buell 1125R lapped the 17-turn, 2.38-mile road course in 1 minute and 32.040 seconds, at an average speed of 89.960 mph. The effort was more than a quarter of a second better than that of second-fastest qualifier, Ryan Gordon of Clemson, S.C., whose No. 75 Touring Sport Ducati 848 posted a lap of 1:32.313 (89.694 mph). Saturday’s schedule consisted of a 90-minute practice session, which was immediately followed by a 10-minute break and the 20-minute qualifying session. Higbee was pleased with the result and with the way his team tweaked the No. 8 Buell during the limited track time. “Our practice time was cut a little short because we came in and swapped shocks on the bike. We wanted to come in and make some changes,” said Higbee, who took part in an AMA race at Barber several years ago. “I think tire conservation is going to be a big part of the race; it’s so hot that the track is really hard on tires. The bike is oversteering a bit right now, so we might make some changes to try to improve it”¦ or else we’ll be out there flat-tracking it.” Asked about the significance of starting up front on Sunday, Higbee deadpanned, “It’s just a pole position, but hopefully it’s a good indication of how things will go in the race tomorrow. It’s going to be interesting. We feel like we’ve got a bit of momentum going after our win at Road America.” On Sunday, Higbee will be teamed with Mike Smith of Canton, Ga. Ryan Gordon will start Sunday’s Barber 500K from the second position. The No. 75 Touring Sport Ducati team earned runner-up finishes in the season’s first two races (at Daytona and Virginia) and are hoping to get back on form following a fourth-place showing in Round 3 at Road America. Gordon is teamed with Ryan Elleby (Powder Springs, Ga.) and Frank Shockley (Greenville, S.C.). Ty Howard of Weatherford, Texas will line up third on Sunday on the No. 1 Aprilia USA / Lloyd Brothers Motorsports Aprilia Tuono 1000R. Howard is pleased with his spot considering today’s practice and qualifying sessions were the first time this particular bike has been pushed to the limit on the racetrack. “We struggled out there a little bit; we don’t quite have the right setup yet,” said Howard, whose team enters the weekend as the series’ points leader on the strength of wins in the first two rounds. “With just one practice session and the time split between two riders [teammate Mike Himmelsbach of Quakertown, Pennsylvania] it makes it hard to get the setup dialed in. Going into qualifying we weren’t sure about how fast our setup was”¦ and it wasn’t. We just worked through it and it’s also the first time this bike has really been ridden at race pace, so we know we have some stuff to do for tomorrow.” The No. 6 Aprilia USA / Lloyd Brothers Motorsports Aprilia Tuono 1000R will start fourth on Sunday (ridden by Zac Chapman of Weatherford, Texas and Henry Wiles of Blanchard, Mich.) in front of the No. 55 Crozier Motorsports Ducati 848 (ridden by Mark Crozier of Fort Valley, Ga. and Nathan Dressman of Clarkston, Mich.). Leading the way in BMW GrandSport Twins (GST) class qualifying on Saturday was Justin Filice on the No. 59 RightsForBikers.com Ducati PS 1000LE. The Modesto, Calif. racer lapped the Barber circuit in a time of 1:35.536 (86.668 mph), which was seventh fastest overall of the 25 teams (in the three divisions) that took to the track during qualifying. Filice set his fast time on the team’s 10th and final qualifying lap of the session. “On that last lap, I was behind one of the ST bikes and my tires were starting to go off and get a little slippery, so I backed it off a little. Then one of the ST bikes went around me and I said, ‘I’ll give it another shot,’ and followed him around for a little bit and ended up clicking off a [one minute and] 35.5. My team didn’t even tell me until I came into the pits.” Filice feels comfortable heading into Sunday’s Barber 500K. “I’m riding with Armando Ferrer and Rodolfo Ramirez. They both did a great job today, getting down into the [one minute and] 37s, I believe. I think we’re going to be very competitive tomorrow. I’m going to start and try to get a little bit of a gap. The plan is for them to maintain and I’ll ride the last 40 minutes or so.” The No. 77 Touring Sport Ducati PS 1000LE (ridden by Pete Friedland of Columbia, S.C., Brad Phillips of Greer, S.C. and Frank Shockley of Greenville, S.C.) was second fastest of the GST teams during qualifying, ahead of the No. 23 Motocorse Bimota DB5 of Chris Boy (Ft. Lauderdale, Fla.), Greg Melka (Tampa, Fla.) and Kevin Mendez (Davie, Fla.). The No. 66 M4 AVTEQ Suzuki SV650 was the class of the field in the Sport Twins (ST) division during qualifying. Rider Dane Westby of Tulsa, Okla. toured the Barber circuit in 1:36.994 (85.366 mph). Westby heads into Sunday’s feature race with an open mind, in terms of strategy. “I’m not really sure what our plan is; I’m just getting on it and riding it until they tell me to get off.” The points-leading No. 9 Pair-A-Nines Kawasaki EX650 of Jimmy Filice (Daytona Beach, Fla.) and Jay Springsteen (Lapeer, Mich.) were the next-fastest of the ST qualifiers, timing in at 1:38.432 (84.119 mph). Behind them were the No. 67 M4 AVTEQ Suzuki SV650 of Ryan O’Donnell (Dallas, Texas) and Russ Wikle (Huntsville, Ala.). The Barber 500K gets the green flag at 8:00 a.m. Sunday morning. The race is scheduled for two hours and thirty minutes. The SunTrust MOTO-ST Series is organized and sanctioned by Professional Motorsports Productions (PMP) of Toronto, Ontario, Canada and the Grand American Road Racing Association, based in Daytona Beach, Fla., provides the series with administrative and commercial support. Learn more about MOTO-ST at www.moto-st.com.

2009 AMA Pro Racing Daytona Superbike Rules

0

Daytona Superbike Equipment Regulations All machines eligible for participation in Daytona Superbike must be approved by AMA Pro Racing and homologated by the manufacturer or sanctioning body. Machines currently eligible for homologation by their manufacturer or distributor for competition in 2009 are: Aprilia Tuono BMW HP2 Sport Buell 1125R Ducati 848 Ducati S4R Honda CBR600RR Kawasaki Ninja ZX-6R KTM Super Duke MV Brutale 910S Suzuki GSX-R600 Triumph Daytona 675 Yamaha YZF-R6 Each homologated machine will have a published Technical Information Form (TIF) containing the AMA approved specifications required for competition. Specifications will include, but not be limited to make, model, year, original displacement, and special allowances (if any) for this specific homologated machine. The original TIF may be modified to enhance or reduce the performance of the machine based upon actual competition experience. Unless otherwise specified, all parts must originate from the same make/model as the homologated machine, meaning no up-dating or back-dating is permitted 1. HORSEPOWER AND WEIGHT LIMITS A. Minimum weight is 360 lbs in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. B. Once the machine weight has been established, the motorcycle will be tested for power output on the official series dynamometer. Power is limited to one (1) horsepower for every three (3) pounds of machine weight, up to a maximum of 140 horsepower. Fuel may be added to allow for the dynamometer testing after the official weight has been recorded. C. In no case may more than 25 lbs of ballast be added to any machine, said ballast to be added/fastened in accordance with approved mounting procedures. D. If necessary, specific motorcycles may be allowed a variance from the standard power to weight ratio to ensure parity in competition. Where such variances are allowed, they will be published on the TIF for the machines affected. E. Combined motorcycle and rider weights will be used to determine power limits starting in the 2010 season. 2. TIRES A. XXXXXX is the Official Tire of AMA Pro Road Racing and only tires produced by XXXX and mounted at the meet may be used in competition. B. The number of available compounds, configurations, and quantities available for use at each event will be announced coincident with the announcement of the Official Tire of the series and may be altered during the course of the 2009 season per safety, wear and related experience. 3. FUEL A. Official Fuel – The Official Fuel of AMA Pro Racing is XXXXXXXX and its exclusive use in unadulterated form shall be mandatory. B. Only air may be mixed with the fuel as an oxidant, and no other substances, chemicals and/or liquids whatsoever shall be added, combined, mixed and/or introduced to said Official Fuel whether intentionally or unintentionally unless approved in advance in writing by the AMA for use by all competitors. C. All competitors must use the official fuel, as supplied by the manufacturer at the track, during all on-track sessions. D. All motorcycles must prominently display the appropriate unmodified official fuel company decal on the motorcycle at all times. E. AMA Pro Racing has the right to sample a competitor’s fuel at any time. F. Competitors are responsible for the safe and proper handling and security of their fuel from when it is dispensed to them until it is used. G. Competitors are responsible for properly disposing of all unused fuel. 4. WHEELS/BRAKES A. Original equipment wheels must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. (1) Front wheels = 17″ x 3.5″ all machines (2) Rear wheels = 17″ x 5.5″ or 17″ x 6″ B. Original equipment brake calipers must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. C. Aftermarket brake pads and lines may be substituted by homologated units appearing on the Eligible Equipment List. D. The brake master cylinders may be substituted by homologated units appearing on the Eligible Equipment List. E. With approval of the Technical Inspector, front wheel spacers may be made “captive”. F. With approval of the Technical Inspector, rear wheel spacers may be made “captive”, and a caliper retaining device may be used. Chain adjuster must be OEM. 5. FRONT SUSPENSION A. Original front forks must be retained, including inner and outer tubes, fork bottoms, caliper mounts, axles and spacers. B. Aftermarket Cartridge kits appearing on the Eligible Equipment List are permitted and aftermarket fork caps may be substituted. C. A steering damper may be installed with a homologated unit appearing on the Eligible Equipment List. D. A fork brace may be installed with a homologated unit appearing on the Eligible Equipment List. E. Triple Clamps may be substituted with a homologated unit appearing on the Eligible Equipment List. F. Front suspension modifications are limited to: (1) Internal parts may be modified consistent and within the foregoing restrictions, including substitution of springs, change of shims and/or spacers, and addition of kit/aftermarket valving units appearing on the Eligible Equipment List. (2) External Compression Adjusters may be modified/changed. (3) Steering Head inserts to adjust rake may be used as long as no part of the frame is modified. 6. REAR SUSPENSION A. The original model, stock swingarm must be retained, unchanged, except that the axle adjustment opening/slot may be lengthened, with the permission of the Technical Inspector. B. The rear shock linkage may be substituted with a homologated unit appearing on the Eligible Equipment List. C. The rear shock may be modified or replaced by units appearing on the Eligible Equipment List. 7. FRAME/ADJUSTABLE PIVOT A. Unless otherwise provided for on the TIF, the original frame must be used. Unnecessary brackets may be removed. B. Adjustable swingarm pivots are permitted, but no modifications to the frame or swingarm can be made to allow this adjustability. 8. BODYWORK/CONTROLS/APPEARANCE A. Aftermarket, OEM-style bodywork and custom fairing mounts may be used. B. The fairing must match the shape of the OEM machine in silhouette and profile and the AMA shall have the right to use templates and go-no-go devices therefor. 1) An oil retaining, “sealed” lower fairing is mandatory. C. The stock gas tank must be used, but aftermarket gas caps are allowed. D. A front fender must be mounted. E. Aftermarket footpegs, clip-on bars, shift/brake mechanisms and fasteners may be used. F. Non-standard “Kill Switches” must not be spring loaded and must be well marked. G. Titanium Fasteners are not permitted. H. Tail sections may be increased in size to allow for required number display. Final approval rests with the Chief Technical Inspector. (1) AMA Pro retains the right to require number plates on machines with small or unusually sized or shaped tail sections. I. Numbers must be a minimum of 8 inches high and in a clear contrasting color to the background area on which they are displayed. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) No modifications are allowed except as follows: a. Cylinder head, cylinder and crankcase gasket surfaces only may be machined for increased compression. All other surfaces of the cylinder head, cylinder and crankcases must remain absolutely as homologated with no metal removal. b. Light cleaning of gasket surfaces with steel wool, Scotch-Brite®, etc. is permitted. Deburring radius of machined area must not be greater than 0.020 inches or 0.5mm. c. The cylinder head gasket may be changed. d. The valves, valve seats, guides, springs, tappets, oil seals, shims, cotter valve, spring base and spring retainers must be as originally produced by the manufacturer for the homologated machine. Valve spring shims are allowed. B. Camshaft (1) No modifications are allowed. (2) At the technical checks: for direct cam drive systems, the cam lobe lift is measured; for non direct cam drive systems (i.e. with rocker arms), the valve lift is measured. (3) The timing of the camshaft is free. C. Cam Sprockets (1) No dimensional modifications are allowed. (2) Cam sprockets may be slotted solely for the purpose of altering cam timing. (3) Press-on cam sprockets may be replaced with aftermarket steel bolt-on cam sprockets and adapters. (4) Aftermarket cam chain tensioners are permitted. D. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. E. Oil Pumps and Oil Lines (1) No pump modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. F. Connecting Rods (1) No modifications are allowed (including polishing and lightening). G. Pistons (1) No modifications are allowed (including polishing and lightening). H. Piston Rings (1) No modifications are allowed. I. Piston Pins and Clips (1) No modifications are allowed. J. Cylinders (1) No modifications are allowed except as provided for above. K. Crankcase and all other Engine Cases (i.e. ignition case, clutch case, etc.) (1) No modifications to the crankcases are allowed except as provided for above. (2) Lateral (side) covers may be altered, modified or replaced. If replaced, the cover must be made in material of same or higher specific weight and the total weight of the cover must not be less than the original one. (3) On motorcycles where lateral covers or engine cases contain oil, strengthened engine side covers or case guards must be installed. All such protection devices must weigh no less than the original homologated parts and must be approved by the AMA Pro Tech Inspector. L. Transmission/Gearbox (1) Kit-type Electronic “quick shifters” are allowed. (2) Manual “secondary” hand operated kill switch/quick shifters are not allowed. (3) Final drive system, if not by chain, may be modified to chain type, utilizing kits specified on the Eligible Equipment List. (4) Original equipment shift drum detent stars may be modified or replaced with approved, homologated aftermarket parts. (5) Other modifications to gearbox or selector mechanism are not allowed. M. Countershaft sprocket, rear wheel sprocket, chain pitch and size can be changed. (1) The sprocket cover can be modified. N. Stock carb bodies or stock fuel injection systems must be used, but carb internals, velocity stacks and injection management systems may be altered or replaced. O. Injectors must be stock and unaltered from the original specification and manufacture. P. Aftermarket exhaust systems appearing on the Eligible Equipment List may be installed. Q. “Dry Clutches” are only permitted when used on the equivalent OE production model. R. Aftermarket “Slipper” clutches appearing on the Eligible Equipment List are permitted. S. Homologated engine control unit (ECU), must be either: (1) As homologated and inner software can be changed; (2) Or the ECU kit model (produced and/or approved by the machine Manufacturer) can be used. (3) A special connector can be used to connect the kit ECU and the original wire loom. (4) Series provided Engine Control Units may be required in 2010 and beyond. 10. AIR BOX/INTAKE/SCOOPS A. Original equipment air box is required, without modification. B. An air filter is required. Original equipment air filter and air filters appearing on the Eligible Equipment List are permitted. C. Ram air systems are permitted if specified and used on the homologated motorcycle. Ducts and scoops, must be identical in specification to the original equipment system. 11. POST QUALIFYING/POST RACE TECH A. Immediately following each qualifying session or race, the top three finishers plus other motorcycles chosen at random at the discretion of the AMA will be tested on the Official Series Dynamometer to verify power. B. Other than the motorcycle’s throttle/twist grip, switches or any other device and/or methodology designed to and/or having the ability or potential to affect the horsepower readings during dynamometer testing are strictly prohibited. C. Any entrant, rider, crew member and/or entrant affiliate (who are not manufacturers of homologated motorcycles), who attempts to and/or does alter the performance of his/her/their machine following any competition event, in an effort to affect the dynamometer or weight results, will be disqualified from the meet and suspended from AMA Pro Road Racing participation for a period of no less than one year, and assessed a $50,000.00 fine which must be paid in full before reinstatement. A second offense will result in a lifetime ban for the offending entrant and/or entity. D. Any entrant, entrant affiliate and/or contractor who is/are manufacturers of homologated motorcycles, who attempts to and/or does alter the performance of its/their machine following any competition event, in an effort to affect the dynamometer or weight results, will be disqualified from the meet and suspended from AMA Pro Road Racing participation for a period of no less than one year, and assessed a $250,000.00 fine which must be paid in full before reinstatement. A second offense will result in a loss of approval for the homologated machine used in the meet where the offense took place, thereby rendering it ineligible for use by any and all entrants for a period of twelve (12) months. E. Machines unable to make post qualifying or post race tech and complete their dynamometer runs for any reasons, including major crashes or major mechanical failures will be penalized. Reasonable allowances may/will be made for minor mechanical failures that can be repaired, under strict supervision, in a reasonable amount of time and that do not have any bearing on performance or weight. Reasonable allowances may/will also be made for minor crashes on machines that can be ridden back to pit lane. Determination of ‘minor’ will be at the sole discretion of the Tech Inspector. F. In the instance where a motorcycle on the post-race dynamometer produces one run where that motorcycle registered within (but not more than) one horsepower in excess of the horsepower limit, that motorcycle will be re-tested at the end of that class/group, time allowing and at the request of the entrant. If that motorcycle again measures/tests any way in excess of the allowable horsepower limit , that machine will be penalized as per the Rule book. If that machine reads within the guidelines in the dynamometer re-do, no penalty will be assessed. G. Motorcycle weights will be checked immediately following qualifying or races, in the same condition in which they finish the activity, including all fluids such as oil, water and fuel. H. No fluid and/or any other item(s) may be added to the motorcycle prior to the determination of weight. Subsequent to official weight verification, fuel may be added for the purpose of completing the required dynamometer verification.

2009 AMA Pro Racing American Superbike Rules

0

All machines eligible for participation in American Superbike must be approved by AMA Pro Racing and homologated by the manufacturer or the sanctioning body. Each homologated machine will have a published Technical Information Form (TIF) containing the AMA approved specifications required for competition. Specifications will include, but not be limited to make, model, year, original displacement. The original TIF may be modified to enhance or reduce the performance of the machine based upon actual competition experience. Unless otherwise specified, all parts must originate from the same make/model as the homologated machine, meaning no up-dating or back-dating is permitted. 1. DISPLACEMENT CAPACITIES AND WEIGHT LIMITS A. Minimum weight is 370 lbs in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. B. Displacement capacities (1) 4 cylinders Over 600 cc up to 1000 cc 4-stroke (2) 3 cylinders Over 750 cc up to 1000cc 4-stroke (3) 2 cylinders Over 850 cc up to 1200 cc 4-stroke (4) The displacement capacities must remain at the homologated size. Modifying the bore and stroke to reach class limits is not allowed. 2. TIRES A. XXXXXX is the Official Tire of AMA Pro Road Racing and only tires produced by XXXX and mounted at the meet may be used in competition. B. The number of available compounds, configurations, and quantities available for use at each event will be announced coincident with the announcement of the Official Tire of the series and may be altered during the course of the 2009 season per safety, wear and related experience. 3. FUEL A. Official Fuel – The Official Fuel of AMA Pro Racing is XXXXXXXX and its exclusive use in unadulterated form shall be mandatory. B. Only air may be mixed with the fuel as an oxidant, and no other substances, chemicals and/or liquids whatsoever shall be added, combined, mixed and/or introduced to said Official Fuel whether intentionally or unintentionally unless approved in advance in writing by the AMA for use by all competitors. C. All competitors must use the official fuel, as supplied by the manufacturer at the track, during all on-track sessions. D. All motorcycles must prominently display the appropriate unmodified official fuel company decal on the motorcycle at all times. E. AMA Pro Racing has the right to sample a competitor’s fuel at any time. F. Competitors are responsible for the safe and proper handling and security of their fuel from when it is dispensed to them until it is used. G. Competitors are responsible for properly disposing of all unused fuel. 4. WHEELS/BRAKES A. Original equipment wheels must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. (1) Front wheels = 17″ x 3.5″ all machines (2) Rear wheels = 17″ x 5.5″ or 17″ x 6″ (See TIF for each machine) B. Original equipment brake calipers must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. C. Aftermarket brake pads and lines may be substituted by homologated units appearing on the Eligible Equipment List.. D. The brake master cylinders may be substituted by homologated units appearing on the Eligible Equipment List. E. With approval of the Technical Inspector, front wheel spacers may be made “captive”. F. With approval of the Technical Inspector, rear wheel spacers may be made “captive”, and a caliper retaining device may be used. Chain adjuster must be OEM. 5. FRONT SUSPENSION A. Original front forks must be retained, including inner and outer tubes, fork bottoms, caliper mounts, axles and spacers. B. Aftermarket Cartridge kits appearing on the Eligible Equipment List are permitted and aftermarket fork caps may be substituted. C. A steering damper may be installed with a homologated unit appearing on the Eligible Equipment List. D. A fork brace may be installed with a homologated unit appearing on the Eligible Equipment List. E. Triple Clamps may be substituted with a homologated unit appearing on the Eligible Equipment List. F. Front suspension modifications are limited to: (1) Internal parts may be modified consistent and within the foregoing restrictions, including substitution of springs, change of shims and/or spacers, and addition of kit/aftermarket valving units appearing on the Eligible Equipment List. (2) External Compression Adjusters may be modified/changed. (3) Steering Head inserts to adjust rake may be used as long as no part of the frame is modified. 6. REAR SUSPENSION A. The original model, stock swingarm must be retained, unchanged, except that the axle adjustment opening/slot may be lengthened, with the permission of the Technical Inspector. B. The rear shock linkage may be substituted with a homologated unit appearing on the Eligible Equipment List. C. The rear shock may be modified or replaced by units appearing on the Eligible Equipment List. 7. FRAME/ADJUSTABLE PIVOT A. Unless otherwise provided for on the TIF, the original frame must be used. Unnecessary brackets may be removed. B. Adjustable swingarm pivots are permitted, but no modifications to the frame or swingarm can be made to allow this adjustability. 8. BODYWORK/CONTROLS/APPEARANCE A. Aftermarket, OEM-style bodywork and custom fairing mounts may be used. B. The fairing must match the shape of the OEM machine in silhouette and profile and the AMA shall have the right to use templates and go-no-go devices therefor. 1) An oil retaining, “sealed” lower fairing is mandatory. C. The stock gas tank must be used, but aftermarket gas caps are allowed. D. A front fender must be mounted. E. Aftermarket footpegs, clip-on bars, shift/brake mechanisms and fasteners may be used. F. Non-standard “Kill Switches” must not be spring loaded and must be well marked. G. Titanium Fasteners are not permitted. H. Tail sections may be increased in size to allow for required number display. Final approval rests with the Chief Technical Inspector. (1) AMA Pro retains the right to require number plates on machines with small or unusually sized or shaped tail sections. I. Numbers must be a minimum of 8 inches high and in a clear contrasting color to the background area on which they are displayed. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) No modifications are allowed except as follows: a. Cylinder head, cylinder and crankcase gasket surfaces only may be machined for increased compression. All other surfaces of the cylinder head, cylinder and crankcases must remain absolutely as homologated with no metal removal. b. Light cleaning of gasket surfaces with steel wool, Scotch- Brite®, etc. is permitted. Deburring radius of machined area must not be greater than 0.020 inches or 0.5mm. c. The cylinder head gasket may be changed. d. The valves, valve seats, guides, springs, tappets, oil seals, shims, cotter valve, spring base and spring retainers must be as originally produced by the manufacturer for the homologated machine. Valve spring shims are allowed. B. Camshaft (1) No modifications are allowed. (2) At the technical checks: for direct cam drive systems, the cam lobe lift is measured; for non direct cam drive systems (i.e. with rocker arms), the valve lift is measured. (3) The timing of the camshaft is free. C. Cam Sprockets (1) No dimensional modifications are allowed. (2) Cam sprockets may be slotted solely for the purpose of altering cam timing. (3) Press-on cam sprockets may be replaced with aftermarket steel bolt-on cam sprockets and adapters. (4) Aftermarket cam chain tensioners are permitted. D. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. E. Oil Pumps and Oil Lines (1) No pump modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. F. Connecting Rods (1) No modifications are allowed (including polishing and lightening). G. Pistons (1) No modifications are allowed (including polishing and lightening). H. Piston Rings (1) No modifications are allowed. I. Piston Pins and Clips (1) No modifications are allowed. J. Cylinders (1) No modifications are allowed except as provided for above. K. Crankcase and all other Engine Cases (i.e. ignition case, clutch case, etc.) (1) No modifications to the crankcases are allowed except as provided for above. (2) Lateral (side) covers may be altered, modified or replaced. If replaced, the cover must be made in material of same or higher specific weight and the total weight of the cover must not be less than the original one. (3) On motorcycles where lateral covers or engine cases contain oil, strengthened engine side covers or case guards must be installed. All such protection devices must weigh no less than the original homologated parts and must be approved by the AMA Pro Tech Inspector. L. Transmission/Gearbox (1) Kit-type Electronic “quick shifters” are allowed. (2) Manual “secondary” hand operated kill switch/quick shifters are not allowed. (3) Final drive system, if not by chain, may be modified to chain type, utilizing kits specified on the Eligible Equipment List. (4) Original equipment shift drum detent stars may be modified or replaced with approved, homologated aftermarket parts. (5) Other modifications to gearbox or selector mechanism are not allowed. M. Countershaft sprocket, rear wheel sprocket, chain pitch and size can be changed. (1) The sprocket cover can be modified. N. Stock carb bodies or stock fuel injection systems must be used, but carb internals, velocity stacks and injection management systems may be altered or replaced. O. Injectors must be stock and unaltered from the original specification and manufacture. P. Aftermarket exhaust systems appearing on the Eligible Equipment List may be installed. Q. “Dry Clutches” are only permitted when used on the equivalent OE production model. R. Aftermarket “Slipper” clutches appearing on the Eligible Equipment List are permitted. S. Homologated engine control unit (ECU), must be either: (1) As homologated and inner software can be changed; (2) Or the ECU kit model (produced and/or approved by the machine Manufacturer) can be used. (3) A special connector can be used to connect the kit ECU and the original wire loom. 10. AIR BOX/INTAKE/SCOOPS A. Original equipment air box is required, without modification. B. An air filter is required. Original equipment air filter and air filters appearing on the Eligible Equipment List are permitted. C. Ram air systems are permitted if specified and used on the homologated motorcycle. Ducts and scoops, must be identical in specification to the original equipment system. 11. POST QUALIFYING/POST RACE TECH A. Immediately following each qualifying session or race, the top three finishers plus other motorcycles chosen at random at the discretion of AMA Pro will be secured for inspection by AMA Pro staff members. B. Motorcycle weights will be checked immediately following qualifying or races, in the same condition in which they finish the activity, including all fluids such as oil, water and fuel. C. No fluid and/or any other item(s) may be added to the motorcycle prior to the determination of weight.

2009 AMA Pro Racing Factory Superbike Rules

0

2009 BASIC EQUIPMENT REGULATIONS FOR ROAD RACING COMPETITION Factory Superbike Equipment Regulations All machines eligible for participation in Factory Superbike must be approved by AMA Pro Racing and homologated by the manufacturer. All items not mentioned in the following articles must remain as originally produced by the manufacturer for the homologated machine. EVERYTHING THAT IS NOT AUTHORIZED AND PRESCRIBED IN THESE REGULATIONS IS STRICTLY FORBIDDEN. In addition, every motorcycle entered must meet the requirements listed in General Equipment Standards. 1. DISPLACEMENT CAPACITIES AND WEIGHT LIMITS A. Minimum weight in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. (1) 4 cylinder 375 pounds (2) 2 cylinder 390 pounds B. Displacement capacities (1) 4 cylinders 749cc up to 1000 cc 4-stroke. (2) 2 cylinders 901cc up to 1200 cc 4-stroke (3) Engine type, configuration, stroke and any modifications of engine components to alter the stock OEM firing order of the cylinders are not permitted. (4) The displacement capacities must remain at the homologated size. Modifying the bore and stroke to reach class limits is not allowed. 2. TIRES A. Any tire approved by the tire manufacturer for racing is allowed. 3. FUEL A. To be determined. 4. WHEELS/BRAKES A. Wheels (1) Wheels and associated parts may be modified or replaced from those fitted to the homologated motorcycle. (2) Carbon fiber or carbon composite wheels are not allowed. (3) Bearings, seals and axles may be altered or replaced from those fitted to the homologated motorcycle. (4) Rear wheel sprocket and brake rotor must remain with the wheel unless part of the original homologated design. (5) Maximum rear wheel rim width: 6.25 in. B. Brakes (1) Front and rear master cylinder including lever/pedal may be modified or replaced from those fitted to the homologated motorcycle. (2) Front and rear calipers may be modified or replaced from those fitted to the homologated motorcycle. (3) Brake pads or shoes may be modified or replaced from those fitted to the homologated motorcycle. (4) Brake hoses and brake fittings may be modified or replaced from those fitted to the homologated motorcycle. (5) Brake discs may be modified or replaced from those fitted to the homologated motorcycle. (6) The use of carbon fiber, carbon composite or titanium materials for brake discs is not allowed. 5. FRONT SUSPENSION A. Front forks in whole or part may be modified or replaced from those fitted to the homologated motorcycle. B. Front Forks must be the same type on the homologated motorcycle (leading link, telescopic, upside down, etc.). C. The upper and lower fork clamps (triple clamp, fork bridges) including steering stem, can be changed or modified. D. Steering damper may be added, relocated or replaced with an aftermarket damper. E. The steering damper cannot act as a steering lock limiting device. F. Active, semi-active or computer-controlled suspension units are not permitted. 6. REAR SUSPENSION A. Rear suspension unit can be changed but a similar unit must be used (i.e. dual or single shock). B. The rear suspension linkage may be modified or replaced. 7. FRAME A. Frame and Sub Frame (1) The main Frame must remain as originally produced by the manufacturer for use on the homologated motorcycle with the following modifications allowed: (2) Strengthening gussets and tubes may be added, but none may be removed. (3) Accessory brackets (radiator, shock reservoir, stands, etc.) may be changed, relocated, added or removed. Holes may be drilled only for the purpose of attaching brackets or other components. (4) The homologated dimensions and the position of the steering head, engine, swing arm pivot point, rear shock, and suspension linkage mounting points must remain as homologated on the original machine. (5) The use of offset bearing races for the purpose of altering the steering angle is allowed. (6) The swing arm pivot location may only be adjusted if the design was part of the homologated frame. (7) Rear sub frame may be modified or replaced, but the material must remain as homologated. (8) Polishing of frame materials is not allowed. (9) Frame must display vehicle identification number. B. Swingarm (1) Swingarm may be modified or replaced. (2) The use of carbon fiber or Kevlar® materials are not allowed if not homologated on the original machine. (3) Rear wheel stand mounts may be added to the swingarm by welding or by bolts. Brackets must have rounded edges (with a large radius). Mounting bolts must be recessed. 8. BODYWORK/CONTROLS/APPEARANCE A. Fairing and Bodywork (1) Fairing and bodywork, including the front fender and windscreen may be modified or replaced with aftermarket parts which resemble the originally approved parts in design and which maintain similar dimensions. (2) Construction must be of plastic or fiberglass (no carbon or carbon composite fiber) (3) See Fairing and Bodywork under General Equipment Standards for other restrictions and fluid containment. (4) With permission from the Race Manager or the Chief Technical Inspector, fairing or bodywork may be removed only if damaged at that particular meet. This does not include the oil retention portion of the lower fairing. B. Seat (1) Seat may be altered or replaced from those fitted to the homologated motorcycle. (2) The top portion of the rear bodywork around the seat may be modified to a solo seat. (3) The solo seat then must incorporate the rear number plate. (4) The appearance from both front rear and profile must conform in principle to the homologated shape. (5) The seat/rear cowl must allow for proper number display. (6) All exposed edges must be rounded. (7) Construction must be of plastic or fiberglass (no carbon or carbon composite fiber). C. Instrument Panel (1) Aftermarket instrument panels are allowed. (2) A shift/indicator light may be added even if one did not exist from the factory. D. Foot Rest/Foot Controls (1) Foot rest/foot controls may be may be modified, relocated or replaced from those fitted to the homologated motorcycle. (2) Foot rests may be rigidly mounted or a folding type which must incorporate a device to return to the normal position. (3) The end of the footrest must have an 8mm solid spherical radius. E. Handle Bars and Hand Controls (1) Handle bars, hand controls and cables may be altered or replaced from those fitted to the homologated motorcycle. (2) Engine stop switch must be located on the handlebars. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) Cylinder heads must remain as homologated with the following modifications allowed. (2) Porting and polishing of the cylinder head and INTAKE MANIFOLD normally associated with individual tuning such as gas flowing of the cylinder head, including the combustion chamber is allowed. (3) Welding or the addition of material is allowed. (4) The compression ratio is unrestricted. (5) Combustion chamber may be modified. (6) Replacement valve seats and guides are permitted. B. Cylinders (1) Only the following modifications to the cylinders are allowed. Cylinder head gasket surface may be machined to allow the adjustment of compression ratio or resurfacing to repair a warped cylinder surface deck. (2) Homologated materials and castings for cylinders must be used. (3) Cylinder liners or coatings may be replaced or added. C. Crankcase and all other Engine Cases (i.e. ignition case, clutch case). (1) Crankcases must remain as homologated. No modifications are allowed. (2) Engine case guards in the form of strengthened engine side covers or approved guards must be installed on certain models. Replacement covers must be no lighter in weight than the stock covers. See Engine under General Equipment Standards. (3) The countershaft cover may be removed. (4) The addition of a crankcase protector at the countershaft is allowed. D. Valves, Springs, and Retainers (1) Aftermarket or modified valves, springs, retainers and other valve-train components are permitted. The original number of valves must be maintained. (2) Valve diameter and minimum weight, including stem, must remain as homologated. (3) Valves must remain in the same location and at the same angle as the homologated model. (4) The material and dimensions of the rocker arms (if any) must remain as homologated. (5) The material of the tappets/buckets must remain as homologated. E. Camshafts and Sprockets (1) The original camshaft may be modified or replaced from those fitted to the homologated motorcycle. (2) The method of drive must remain as homologated. (3) The duration is unrestricted but the lift must remain as homologated. (4) The tensioning devise(s) for the cam chain or cam belt is unrestricted. (5) Cam sprockets can be modified or replaced to allow the degreeing of camshafts. F. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. G. Connecting Rods (1) Connecting rods must remain as homologated. No modifications are allowed. (2) Polishing and lightening is not allowed. H. Pistons (1) Pistons must remain as homologated. No modifications are allowed. (2) Polishing and lightening is not allowed. I. Piston Rings (1) Piston rings must remain as homologated and installed. No modifications are allowed. J. Piston Pins and Clips (1) Piston pins and clips must remain as homologated. No modifications are allowed. K. Oil Pumps and Oil Lines and Water Pumps (1) Oil pump must remain as homologated. Modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. (3) The internal parts of the water pump may be changed or modified. The drive ratio may be changed. The external appearance must remain as homologated. (4) Water lines may be modified or replaced. L. Clutch (1) Clutch type (wet or dry) must remain as homologated. (2) Aftermarket, modified or stock-type clutches with back-torque limiting capabilities are permitted. M. Transmission Shafts and Gear Sets (1) Two options are available for these components: a. Stock transmission shafts and gear sets. a) Undercutting and surface treatments are the only modifications allowed. b. Approved transmission shafts and gear sets. a) Each manufacturer will be permitted one alternative set of gear ratios per approved model. b) Approved shafts and gears may be interchanged with stock components. c) Undercutting and surface treatments are the only modifications allowed. (2) Only shafts and gears sold through the OEM distributor or its dealers are permitted. (3) Approved transmission components must be available individually or as a set to AMA Superbike-licensed riders for the entire current season (or the remaining part of the season). (4) Orders determined to be legitimate by AMA Pro Racing and accompanied by a 50% deposit must be filled within 15 business days of receipt by the OEM distributor or dealer. (5) Retail price of individual approved transmission components may not exceed twice the manufacturer’s suggested retail price of the components they replace. (6) If a manufacturer does not offer optional AMA Pro Racing approved transmission components, then the stock components must be retained. N. Fuel injection system and throttle-body assemblies (1) Fuel injection throttle body assemblies must remain as homologated. (2) Assemblies include all attached parts with the exception of fasteners, cables, cable actuating pulleys, flexible fuel lines, vacuum lines, air box connection tubes and velocity stacks. (3) Variable-length fuel injection intake tract devices that function while the engine is operating are prohibited unless it is standard equipment on the homologated OEM production model. (4) Fuel injectors may be replaced with aftermarket units provided the original mounting locations are maintained and no modifications are made to the throttle body assemblies for injector fitment. The total number of installed injectors must be the same as originally produced. (5) Secondary butterfly valves may be fixed in the open position. (6) Fuel pump and fuel pressure regulator must remain as homologated with no modifications. O. Engine Control System (1) Engine control system may be modified or replaced with aftermarket products. (2) Wiring harness may be modified or replaced. (3) Spark plugs and plug wires may be replaced. (4) Data acquisition is allowed. (5) Aftermarket sensors re permitted. P. Generator (1) The generator may be modified or replaced. (2) The starting system, electrical or manual may be modified or replaced but must work. 10. AIR BOX/INTAKES/FUEL SUPPLY A. Intake Air Boxes (1) Air box must remain as originally produced by the manufacturer on the homologated motorcycle. (2) Air filters, internal flap type valve, sensors and vacuum fittings may be removed, modified, or replaced with aftermarket parts. Any holes in the air box to the outside atmosphere resulting from the removal of components must be completely sealed from incoming air. (3) All incoming air must pass through the original, unmodified air box inlets. (4) Ram air tubes or ducts may be modified, replaced with aftermarket parts or removed. If tubes/ducts are utilized, they must be attached to the original, unmodified air box inlets. (5) Velocity stacks may be modified, replaced with aftermarket parts or removed. The only modification permitted to the air box to allow use of alternate velocity stacks is the removal of internal debris deflectors/plates. B. Fuel Tanks (1) Fuel tank may be modified or replaced provided that it maintains the stock appearance. (2) Non metallic fuel tanks are not allowed. (3) Fuel tanks may be modified to achieve a maximum capacity of 24 liters (6.341 gallons). (4) The fuel cap may be replaced with a quick-fill coupler and additional vent coupling. Both couplers must be installed in the top of the tank. (5) Maximum inner diameter of quick-fill or vent coupler is 63.5mm (2.5″). C. Fuel Supply (1) Fuel petcocks may be modified or replaced. (2) Fuel lines may be replaced. (3) Quick connectors or dry break quick connectors may be used. (4) Fuel vent lines may be replaced. (5) Fuel filters may be added. 11. MISCELLANEOUS A. Exhaust System (1) The exhaust pipes and silencers may be modified or replaced from those fitted to the homologated motorcycle. (2) Catalytic converters must be removed. (3) For safety reasons, the exposed edge(s) of the exhaust pipes(s) outlet(s) must be rounded to avoid sharp edges. B. Radiators and oil coolers (1) The original radiator or oil cooler may be modified or replaced from those fitted to the homologated motorcycle. (2) Additional radiators and oil coolers are allowed. (3) Oil coolers must not be mounted on or above the rear mudguard. (4) The appearance from the front, rear and profile of the machine must in principle conform to the homologated shape after the addition of additional radiators or oil coolers. C. The following items may be modified or replaced from those fitted to the homologated motorcycle. (1) Any type of lubrication, brake or suspension fluid may be used. (2) Any type of spark plug and plug cap may be used. (3) Gasket and gasket material (4) Bearings (ball, roller, taper, plain, etc.) of any type or brand may be used. (5) Fasteners (nuts, bolts, screws etc.) (6) Main wiring harness and connectors. (7) Battery and switches. (8) Countershaft sprocket, rear wheel sprocket and chain. (9) Oil and fuel filters D. The Following Items May Be Removed (1) Instrument and instrument bracket and associated cables. (2) Radiator fan and wiring (3) Cooling system thermostat (4) Chain guard.

DMG Announces 2009 AMA Pro Racing Plans

0

AMA PRO RACING OFFERS THREE SUPERBIKE CLASSES FOR 2009 DAYTONA BEACH, FLORIDA (JULY 19, 2008) – Today DMG released their plan for the 2009 AMA Superbike Series. Last week the contract with AMA and DMG was unanimously approved by the AMA Board of Trustees. In the future, DMG will do business as AMA Pro Racing and further releases will be under that trade name. After four months of meetings and discussions, listening to suggestions, comments, and ideas from the broad spectrum of interested parties, AMA Pro Racing is presenting a program designed to provide exciting competition that will appeal to fans and participants alike. “The program we are releasing today represents the best combination of our vision and the vision shared with us by the manufacturers, promoters, fans, and independent teams” said Roger Edmondson of AMA Pro Racing. The primary classes are Factory Superbike, American Superbike, and Daytona Superbike. Each of the classes has their own regulations and character. Secondary programs include the Red Bull AMA US Rookies Cup and Sun Trust Moto-ST, which will be added at select events. Time will be built into each race weekend format to allow for local special activities, fan-walks on pit road, extended pre-race rider introductions, and post-race podium celebrations, complete with public rider interviews for fans and private briefings for the press. Factory Superbike is a new program, free from the constraints of attempts to balance the resources of the factory teams to those of private entries. Featured are liter class sport bikes, operating at the highest level of technology and performance. Plans call for full implementation of FIM World Superbike rules by 2011, but to ease the transition from current equipment, in 2009 Factory Superbikes will be prepared to the specifications agreed to in 2007 by the AMA Rules Committee and manufacturers. Honda, Suzuki, Kawasaki and Yamaha, have all requested use of those rules for 2009. The required Factory Pro license will only be issued to riders with a proven record of experience and performance at the top level of the sport. Other features of this new competition include single-bike qualifying, open tire selection, and unlimited testing. Factory Superbike will be the final race on most event weekends. “Works bikes, salaried star riders, rules written by and requested by the manufacturers, special tires, no-holds barred superbike racing by the strongest teams in America…..what more could a racing fan ask for?” said Edmondson. “It will be a shooting war among the big guns and the meek need not apply.” American Superbike is for the same big-bore machines as Factory Superbike, but at a lower level of modification and performance. As in FIM World Superbike, there will be a single tire supplier. All approved machines and after-market parts will be homologated, and must be available to all competitors. Testing will be limited to reduce costs to the teams and sponsors. “SuperPole” qualifying for the ten fastest riders in timed practice will set the front of the grid. Riders in American Superbike must have a Factory Pro or Superbike Pro license. Motorcycles entered in American Superbike may not be entered in Factory Superbike. Daytona Superbike departs from the traditional displacement and weight regulations and introduces power-to-weight and dynamometer controls to limit horsepower. This class is expected to be contested mostly by 600cc four-cylinder motorcycles, however the rules will provide for close competition with 675cc triples and up to 1200cc twins. All approved machines and after-market parts will be homologated, and must be available to all competitors. Daytona Superbike will feature Superpole qualifying, limited testing, single tire and fuel suppliers, and may be contested by all Superbike licensed riders (Factory Pro, Superbike Pro, and Limited Pro). Homologation of motorcycles and approved after-market accessories and parts will begin August 1st. Provisional rules are attached to this release. The Official Rule Book will be published in September.

Updated: Bayliss Wins World Superbike Superpole At Brno

0

FIM Superbike World Championship Brno, Czech Republic July 19, 2008 Superpole Results (all on Pirelli tires): 1. Troy BAYLISS (Ducati 1098 F08), 1:58.345 2. Troy CORSER (Yamaha YZF-R1), 1:58.451 3. Michel FABRIZIO (Ducati 1098 F08), 1:58.853 4. Max BIAGGI (Ducati 1098 RS08), 1:59.069 5. Ryuichi KIYONARI (Honda CBR1000RR), 1:59.318 6. Niccolo CANEPA (Ducati 1098 F08), 1:59.324 7. Fonsi NIETO (Suzuki GSX-R1000), 1:59.360 8. Jakub SMRZ (Ducati 1098 RS08), 1:59.451 9. Max NEUKIRCHNER (Suzuki GSX-R1000), 1:59.497 10. Yukio KAGAYAMA (Suzuki GSX-R1000), 1:59.537 11. Ruben XAUS (Ducati 1098 RS08), 1:59.545 12. Noriyuki HAGA (Yamaha YZF-R1), 1:59.571 13. Carlos CHECA (Honda CBR1000RR), 1:59.587 14. Lorenzo LANZI (Ducati 1098 RS08), 1:59.639 15. Karl MUGGERIDGE (Honda CBR1000RR), 2:00.306 16. Ayrton BADOVINI (Kawasaki ZX-10R), 2:01.161 The Rest of the Grid: 17. David CHECA (Yamaha YZF-R1), 2:00.228 18. Shinichi NAKATOMI (Yamaha YZF-R1), 2:00.232 19. Gregorio LAVILLA (Honda CBR1000RR), 2:00.304 20. Roberto ROLFO (Honda CBR1000RR), 2:00.374 21. Regis LACONI (Kawasaki ZX-10R), 2:00.482 22. Makoto TAMADA (Kawasaki ZX-10R), 2:00.641 23. Shuhei AOYAMA (Honda CBR1000RR), 2:00.905 24. Sebastien GIMBERT (Yamaha YZF-R1), 2:01.059 25. Vittorio IANNUZZO (Kawasaki ZX-10R), 2:01.214 26. Kenan SOFUOGLU (Honda CBR1000RR), 2:01.302 27. Jiri DRASDAK (Honda CBR1000RR), 2:02.373 28. Christian ZAISER (Yamaha YZF-R1), 2:03.118 29. Jason PRIDMORE (Honda CBR1000RR), 2:03.397 30. Milos CIHAK (Suzuki GSX-R1000), 2:03.758 More, from a press release issued by Team YZF Yamaha Nakatomi only 0.007 from the Superpole For less than one hundredth of a second, Shinichi Nakatomi could not qualify for the Superpole. He was in 18th position and he is looking for a good race. He finished 8th in Brno in 2006 and 9th in 2007. On Friday, the Japanese rider was 17th, 1.4 seconds behind the provisional pole position. On Saturday, he barely missed the qualification for the top 16 who go to Superpole even if his lap time was faster than the day before. The team could be proud of the best top speed, the Yamaha R1 being the fastest motorcycle of the whole field. Shinichi Nakatomi: “We worked a lot on the set up and we made some progress, but the other teams too. My times have been faster and faster, but it was the same for the other riders. My feeling is not so bad, even if the grid position is not so good. The times are very close. We worked well on the set up for the race.” Martial Garcia (team-manager): “The practices have been positive, even if the final result is that we are not in Superpole for 0.007, only 1.2 seconds from the best time. We made a good choice of tyres, despite the aggression of the new track surface. We tested on the race distance with lap times between 2.01 and 2.02, which is one second faster than last year. We are confident for the races because the potential is very good.” Qualifying results: 1-Bayliss (Ducati), 2-Corser (Yamaha), 3-Fabrizio (Ducati), 4-Biaggi (Ducati), 5- Kiyonari (Honda)”¦18- Nakatomi (Yamaha) World Championship standings: 1- Bayliss (Ducati) 259, 2- Neukirchner (Suzuki) 210, 3- Checa (Honda) 207, 4- Haga (Yamaha) 191, 5- Corser (Yamaha) 185″¦19- Nakatomi (Yamaha) 24 Round 10 of the Superbike World Championship: August 3 / Brands Hatch (United Kingdom) Team YMF Yamaha Superstock YZF Yamaha Junior Team FIM Cup Superstock 1000 Superstock 600 European Championship Baz 2nd behind Vostarek Brilliant race for Loris Baz who finished second behind the local rider Patrick Vostarek, who is racing here for the 9th time today on this track. Thanks to this great performance, Baz is still leading the championship. Sylvain Barrier qualified in 14th position for the 1000 cc race that will be held tomorrow. Vostarek had the best start and Baz, in third position, was slowed down by the second Rea. Then Baz overtook Rea and was second at the end of the first lap, 1.2 behind Vostarek. He got closer and closer and he was right behind the Czech at half distance after 5 laps. Rea was in third, quite far 10 seconds behind the leaders. After that, Vostarek and Baz had an incredible fight, with the Frenchman taking the lead on lap 8 before Vostarek took the lead back. Both riders arrived together at the finish line, with a little advantage for Vostarek. With this great performance, Loris Baz keeps the championship lead, with now a 7 points advantage over Vostarek. Loris Baz: « A good start was a must not to let Vostarek take too much of a lead. I knew that after 4 laps with the race tyres I was 0.5 to 1 second faster than him. But Gino Rea had a terrific start and he was hard to overtake. I passed him but he passed me back, had a big slide that slowed me down. I finally passed him and had to catch the leader. I was then 0.7 second faster than him on one lap, and he missed the inside of a curve so I caught him. While I was behind him, I tried to see where I could pass him, but it was very difficult because he knows the track very well. I passed him two laps before the end, but after that I could do nothing because my front tyre was no more performing well. I was crossing the front wheel all the time. I had to use my knee to keep my balance. This is a good weekend. My motorcycle was perfect. Thank you very much to the team. » Difficult practices for Sylvain Barrier in the 1000 cc class, because of a small technical problem on Saturday morning during the free session. Then he was fast in the afternoon for the timed session and he was 14th despite a little crash. Martial Garcia (team-manager): “Loris Baz did a very beautiful race. A slower rider was hard to pass in the first lap but Loris passed him and came back right behind the leader. He tried very hard to win this race and his second position makes him stay the leader of the championship. I a very satisfied. Sylvain Barrier had a small technical problem in the morning and he was much faster in the afternoon despite a small crash with no consequence. He is 14th and we are very confident.” FIM Cup Superstock 1000 qualifying results: 1-Roberts (Ducati), 2-Pirro (Yamaha), 3-Berger (Honda), 4-Siméon (Suzuki), 5-Corti (Yamaha)”¦14- Barrier (Yamaha) FIM Cup Superstock 1000 standings: 1- Simeon (Suzuki) 84 points, 2- Roberts (Ducati) 76, 3- Polita (Ducati) 67, 4- Pirro (Yamaha) 63, 5- Berger (Honda) 59″¦25- Barrier (Yamaha) 4 Superstock 600 European Championship race results: 1-Vostarek (Honda), 2- Baz (Yamaha), 3- Rea (Yamaha), 4- Linfoot (Yamaha), 5- Bussolotti (Yamaha), Superstock 600 European Championship standings: 1- Baz (Yamaha) 117 points, 2-Vostarek (Honda) 110, 3- Linfoot (Yamaha) 74, 4- Bussolotti (Yamaha) 71, 5- Rea (Yamaha) 61 More, from a press release issued by Sterilgarda Go Eleven: There are all the makings of a great day for Sterilgarda Go Eleven tomorrow on the occasion of the race of the 9th WSBK round at Brno: Max Biaggi and Ruben Xaus are going to start from the first and the third line respectively, after having shown during all the four practice sessions to have what it takes to confirm to finish in the top positions of both the race. Max Biaggi likes this track, he recorded the pole after the second timed session and he took the first row after the Superpole. Ruben Xaus worked with the bike in race-trim for the whole two days of qualifying before an hitch at the rear damper of his bike prevented him from getting a better result from his Superpole. In Superstock1000 Alex Polita is going to start from the second line. Like his SBK team-mates, the “Pirate” is going to face the race with the goal to take a final place in the first positions. Weather is unpredictable for tomorrow, every kind of situation is expected and all the team are in a state of uncertainty. RUBEN XAUS | Ducati 1098 RS | 11th classified in 1’59.545: “I wished to get more from my Superpole but the rear damper didn’t work as we expected after having analysed the data of the free practices. I will start from the third line after having done a good work and make meaningful improvements on a track on which I have never felt comfortable. I think I can aim to run two good race and I would like to thank the team for the excellent job done”. MAX BIAGGI | Ducati 1098 RS | 4th classified in 1’59.069: “We have done a good job for the two race. In Superpole I would have liked to confirm the pole-position recorded in the second timed session, anyhow the first line is an excellent starting position”. ALEX POLITA | Ducati 1098R | 7th best time in 2’04.734: “I feel confident with the race which I’m going to face with the goal to fight for a final place in the top positions. During the second timed session I improved my time markedly so we needed to make a little setting change in order to increase the traction. Anyhow we are partway through this solution which is going to be test tomorrow during the warm-up”. More, from a press release issued by FGSport Group: Bayliss grabs Superpole with record lap at Brno Troy Bayliss (Ducati Xerox) grabbed Superpole for round 9 of the WSBK championship with a blistering record lap of 1 minute 58.345 seconds at the newly-resurfaced Automotodrom Brno circuit. Today’s pole was the 22nd of the points leader’s career, and his fourth this season, a result that takes him past Carl Fogarty in the all-time pole classification into second behind Troy Corser on 42. Bayliss’s chief rival today in Superpole was in fact Corser (Yamaha Motor Italia WSB), who was just one tenth of a second down. Third quickest was Bayliss’s Ducati Xerox team-mate Michel Fabrizio, while fourth went to another Italian Max Biaggi (Sterilgarda Go Eleven Ducati), quickest overall in qualifying. Troy Bayliss: “It hasn’t always looked good on this track for us, especially last year, and it’s been a bit of a bogey track for me as well. I’ve never really had great results here in the past and I’d love to turn that around. When I saw Corser’s lap I knew I had to do a good one to beat that and when Max was out, I would have given him a real pat on the back if he had gone faster than that.” Troy Corser: “There’s always a risk when you go out before the end of the Superpole and set the quickest time, especially when Bayliss is around because I know he’s going to grit his teeth and try and get there. But we’ve got a really good set-up for race tyres tomorrow, we’ve done a pretty good race distance and it’s all looking really good.” Michel Fabrizio: “I really like this circuit and I’ve always gone well here. We’ve done a great job during the weekend and my race pace is pretty good. I wanted to go even better in Superpole but unfortunately there’s a ‘granddad’ alongside me who always pulls out something special. But third is a good result and I’m really satisfied.” Max Biaggi: “I really like the Brno track and love racing here. I think we’ve learnt a lot this weekend and for today fourth place is OK. I wanted to go faster a little bit but it didn’t happen. My team and I have done a good job to get on the front row of the grid, which is good because we’re going to have to start well and be up at the front tomorrow.” The biggest mover today was Ryuichi Kiyonari (Hannspree Ten Kate Honda), who powered to fifth place and a row 2 start in Superpole after qualifying for the one-lap dash in sixteenth. The Japanese rider will be accompanied by WSBK rookie Niccolò Canepa (Ducati Xerox), Spain’s Fonsi Nieto (Suzuki Alstare) and Czech star Jakub Smrz (Guandalini Ducati). Bayliss’s chief rivals in the championship failed to emerge, Max Neukirchner (Alstare Suzuki) and Noriyuki Haga (Yamaha Motor Italia WSB) both qualifying on the third row, while Carlos Checa (Hannspree Ten Kate Honda) is even further behind on row 4. Times: 1. Bayliss T. (AUS) Ducati 1098 F08 1’58.345; 2. Corser T. (AUS) Yamaha YZF-R1 1’58.451; 3. Fabrizio M. (ITA) Ducati 1098 F08 1’58.853; 4. Biaggi M. (ITA) Ducati 1098 RS 08 1’59.069; 5. Kiyonari R. (JPN) Honda CBR1000RR 1’59.318; 6. Canepa N. (ITA) Ducati 1098 F08 1’59.324; 7. Nieto F. (ESP) Suzuki GSX-R1000 1’59.360; 8. Smrz J. (CZE) Ducati 1098 RS 08 1’59.451; 9. Neukirchner M. (GER) Suzuki GSX-R1000 1’59.497; 10. Kagayama Y. (JPN) Suzuki GSX-R1000 1’59.537; 11. Xaus R. (ESP) Ducati 1098 RS 08 1’59.545; 12. Haga N. (JPN) Yamaha YZF-R1 1’59.571; 13. Checa C. (ESP) Honda CBR1000RR 1’59.587; 14. Lanzi L. (ITA) Ducati 1098 RS 08 1’59.639; 15. Muggeridge K. (AUS) Honda CBR1000RR 2’00.306; 16. Badovini A. (ITA) Kawasaki ZX-10R 2’01.161. FIM Supersport World Championship Broc Parkes (Yamaha World Supersport) was again quickest in the second and final WSS qualifying session. The 26 year-old Australian set a record lap of 2 minutes 3.204 seconds ten minutes from the end to grab his fifth successive Supersport pole. Parkes will be joined on the front row by the surprising Dutch rider Barry Veneman (RES Software Suzuki), who qualified ahead of Australians Joshua Brookes (Hannspree Stiggy Motorsport Honda) and points leader Andrew Pitt (Hannspree Ten Kate Honda). The second row is made up of Britain’s Craig Jones (Parkalgar Racing Honda), ahead of Mark Aitchison (Triumph BE1 Racing) and Jonathan Rea (Hannspree Ten Kate Honda) while Finland’s Vesa Kallio (Benjan Racing Honda) scored his best result of the year in eighth. Australian Garry McCoy (Triumph SC) had a nasty crash, suffering a cracked vertebra and a bruised right lung in the process. Times: 1. Parkes B. (AUS) Yamaha YZF-R6 2’03.203; 2. Veneman B. (NED) Suzuki GSX-R600 2’03.452; 3. Brookes J. (AUS) Honda CBR600RR 2’03.562; 4. Pitt A. (AUS) Honda CBR600RR 2’03.590; 5. Jones C. (GBR) Honda CBR600RR 2’03.761; 6. Aitchison M. (AUS) Triumph 675 2’03.775; 7. Rea J. (GBR) Honda CBR600RR 2’03.934; 8. Kallio V. (FIN) Honda CBR600RR 2’04.135. Superstock 1000 FIM Cup A Ducati also took pole position in Superstock 1000 qualifying, the Xerox Junior Team 1098 version of Australian Brendan Roberts, who was pushed hard by Italian Michele Pirro (Yamaha Lorenzini by Leoni). The other two riders on the front row are Maxime Berger (Hannspree IDS Ten Kate Honda) of France and points leader Xavier Simeon (Alstare Suzuki) of Belgium. Four Italians make up row 2, one of the race favourites Claudio Corti (Yamaha Motor Italia Junior Team), Andrea Antonelli (Althea Racing Honda), Alex Polita (Sterilgarda Go Eleven Ducati) and Domenico Colucci (Ducati Xerox Junior Team). Times: 1. Roberts B. (AUS) Ducati 1098R 2’03.685; 2. Pirro M. (ITA) Yamaha YZF-R1 2’03.924; 3. Berger M. (FRA) Honda CBR1000RR 2’03.929; 4. Simeon X. (BEL) Suzuki GSX-R1000 2’04.150; 5. Corti C. (ITA) Yamaha YZF-R1 2’04.156; 6. Antonelli A. (ITA) Honda CBR1000RR 2’04.601; 7. Polita A. (ITA) Ducati 1098R 2’04.734; 8. Colucci D. (ITA) Ducati 1098R 2’04.789. European Superstock 600 Championship – Race Czech youngster Patrick Vostarek (Intermoto Czech Honda) scored his third win in a row at the Automotodrom Brno after a battle right down to the last corner with Loris Baz (YZF Yamaha Junior Team), who still holds on to his points lead in the table. Third place went to Britain’s Gino Rea (StoneBaker Yamaha) who just edged out team-mate Dan Linfoot and Italian Marco Bussolotti (Yamaha Motor Italia Junior Team) for the final podium slot. Results: 1. Vostárek P. (CZE) Honda CBR600RR 19’12.257 (151,926 kph); 2. Baz L. (FRA) Yamaha YZF-R6 0.349; 3. Rea G. (GBR) Yamaha YZF-R6 16.862; 4. Linfoot D. (GBR) Yamaha YZF-R6 17.037; 5. Bussolotti M. (ITA) Yamaha YZF-R6 17.072; 6. Black G. (GBR) Yamaha YZF-R6 17.226; 7. Jezek O. (CZE) Kawasaki ZX-6R 17.454; 8. Biliotti L. (ITA) Honda CBR600RR 22.382. Points (after 6 of 10 rounds): 1. Baz (Yamaha) 117; 2. Vostarek (Honda) 110; 3. Linfoot (Yamaha) 74; 4. Bussolati (Yamaha) 71; 5. Rea (Yamaha) 61; 6. Petrucci (Yamaha) 56; 7. Beretta (Suzuki) 53; 8. Black (Yamaha) 37. More, from a press release issued by Yamaha Racing: Corser just misses Superpole win Troy Corser (Yamaha Motor Italia WSB Team) missed out on his 43rd career Superpole win by a mere 0.106 seconds at the 5.403km Brno circuit today, with only his fellow Australian Troy Bayliss able to beat his time. The fight for the new absolute track record was played out in warm and dry conditions and on qualifying tyres. Corser set a 1’58.451 to take what looked like an unbeatable time, only for Bayliss to fight back. Noriyuki Haga (Yamaha Motor Italia WSB Team) worked hard in session with the team but could not find a set-up that allowed his proven talents at Brno to shine and he now starts the races on Sunday from the third row of the grid, 12th overall. David Checa (Yamaha GMT94) came agonisingly close to joining the top 16 qualifiers in Superpole, but now starts the race from the 17th grid slot. Shinichi Nakatomi (Team YZF Yamaha) was only 0.004 seconds from Checa, in a positive final qualifying session. Sebastien Gimbert (Yamaha GMT94) was 24th after losing some track time in practice today. Troy Corser (2nd – 1’58.451 – Yamaha Motor Italia WSB Team) “It was a shame not to win Superpole when we all put so much effort in but the main thing is that we have a front row start for the races. We have a good set-up for raceday and I think we can make our tyres go race distance at a good pace. We did a good race run this afternoon so it’s all feeling very positive. We have made real improvements in the bike since our last test.” Noriyuki Haga (12th – 1’59.571 – Yamaha Motor Italia WSB Team) “We have had a bit of a problem finding a good set up in some areas, but we have improved there, only to find a few smaller problems in another area. We have improved the feeling and tomorrow we can try another setting in a good direction, and we will see how things are after warm-up. We have already decided on a tyre for the race tomorrow, and I think we can find a better race pace than we can do in one single lap of qualifying, which is really important.” Massimo Meregalli (Team Manager, Yamaha Motor Italia WSB Team) “Everything is working well for Troy and he is happy about the bike and tyres. He made a great Superpole lap, he was so close to adding to his record total. Tomorrow we will try something different on Nori’s side. He has a good record here, so tomorrow I am sure we can find something better for him in warm-up anyway. In the end Nori is a racer on Sunday no matter what set-up he has so I am sure he can do well. Shinichi Nakatomi (18th – 2:00.232 – Team YZF Yamaha) “We changed the machine set up and made some progress but other teams also improved their times. The feeling ended up not so bad even if the grid position was not so good. The times are very close and after final qualifying we made good work to prepare for the race.” More, from a press release issued by Xerox Ducati: BAYLISS ON POLE, FABRIZIO THIRD AND CANEPA SIXTH ON THE GRID FOR TOMORROW’S RACES AT BRNO Brno (Czech Republic) Saturday 19th July: The second qualifying session of the weekend, held this morning, saw all three Ducati Xerox riders improve on the times they set yesterday, to qualify for Superpole in third (Bayliss), seventh (Fabrizio) and eighth place (Canepa). Superpole was action packed from the offset, with an immediate flying lap by Kiyonari, the first rider out, which really set the pace, as the next seven riders to exit were unable to beat his fast time. Niccolo’ Canepa, participating in his very first Superpole here this afternoon, was the first of the three Ducati Xerox riders to go out and completed a near perfect lap to take eventual sixth place on tomorrow’s grid. Michel Fabrizio followed him out, beating the times set by the entire field up until that point. The final group of three riders included Troy Bayliss who really made his Superpole lap count to take pole position for the fourth time this season. Troy Bayliss 1m58.3s “Brno has always been something of a bogey track for me but I hope that this weekend we are finally turning that around. The new surface of the track has really improved the grip which is great news. This morning went well and then in Superpole this afternoon, when I saw Corser’s time, I knew I was going to have to put in a really fast lap to be able to beat it and I managed that, but then Max (Biaggi) went out and I was worried he might in turn beat me. I hope tomorrow stays dry and then we’ll see but I have to say it would be pretty special to have a win here this time around.” Michel Fabrizio 1m58.8s “It’s a circuit that I really like and so I’m happy to get a place on the first row here. We have to see tomorrow whether I can make the good start that I need to really be in the running. We did a long-run this morning and it seemed to go ok but it’s obviously going to be hard tomorrow and I’ll no doubt have to fight once again against the two Troys and Biaggi!” Niccolo’ Canepa 1m59.3s “As it’s the first time that I’ve ever taken part in Superpole I have to say I’m really pleased with my performance. During my Superpole lap I made a small mistake and if it weren’t for that I’d have been a couple of tenths faster I think but I can’t complain with a place on the second row for tomorrow’s race. We’re still planning to make a few more little changes this evening to try during the morning’s warm-up as we could still improve our race pace but for now, I’m more than happy.” More, from a press release issued by Team Alstare Suzuki: SECOND AND THIRD ROWS FOR THE SUZUKI TRIO IN BRNO Team Suzuki Alstare rider Fonsi Nieto finished seventh quickest in Superpole and will start tomorrow’s pair of 20-lap races from the second row of the grid. His team mate Yukio Kagayama will be just behind on row three, with Alstare Suzuki rider Max Neukirchner alongside him. Ducatis dominated the front row of the grid, with Troy Bayliss taking his fourth Superpole of the year. His fellow countryman Troy Corser (Yamaha) is second, with Michel Fabrizio (Ducati) third and Max Biaggi (Ducati) fourth. Fonsi – 7th, 1:59.360 I am happy because today I found a good rhythm over a lot of laps on race tyres and was still going consistently fast at the end of eighteen laps. I made a little mistake in Superpole in the last sector, but the second row of the grid is OK here. So far the weekend has been going well. I am happy with the bike and I don’t think we’ll make any changes in the warm-up tomorrow morning. Every time we go out, the grip improves and I think there will be even more grip tomorrow. Whatever happens, I am going for the podium in both races. Max – 9th, 1:59.497 My Superpole lap was bit funny because I didn’t make any mistakes, felt good on the bike but the time was not good! It was strange because I had a feeling like that in the free practice this afternoon when I was on race tyres. For me the grip was better in the morning than the afternoon when I had a bit of a front end chatter. The third row of the grid is not so good, but the first corner is quite far from start so as long as I can get off the line quickly, I have a chance to be in the lead group straightaway. If I can make two good starts, there is no reason why I cannot get on the podium. Yukio – 10th, 1:59.537 I am not so happy to be on the third row of the grid, but I think that is because my Superpole lap was not so good. I made a little mistake in sector two, lost some time and that was that. I got into a turn a bit too hot, braked a bit too hard and then lost my drive exiting the corner. My biggest problem at the moment is getting the best settings for the electronics. When you have good settings, you can push very hard, but we have not yet found the ideal solution. We will try some changes in the warm-up tomorrow morning and see if we can find the best compromise for this track. Final qualifying 1 Bayliss (Aus-Ducati) 1:58.345, 2 Corser (Aus-Yamaha) 1:58.451, 3 Fabrizio (I-Ducati) 1:58.853, 4 Biaggi (I-Ducati) 1:59.069, 5 Kiyonari (J-Honda) 1:59.318, 6 Canepa (I-Ducati) 1:59.324, 7 Fonsi Nieto (E-Suzuki Alstare) 1:59.360, 8 Smrz (CZ-Ducati) 1:59.451, 8 Max Neukirchner (D-Alstare Suzuki) 1:59.497, 10 Yukio Kagayama (J-Suzuki Alstare) 1:59.537, FRONT ROW FOR XAVI. Team Alstare Suzuki rider Xavi Simeon posted the fourth quickest time in qualifying and will start tomorrow’s sixth round of this year’s Superstock 1000 FIM Cup on the front row of the grid. Aussie Brendan Roberts (Ducati) took pole position this afternoon, with Michele Pirro (Yamaha) second and Maxime Berger (Honda) third. Xavi – 4th, 2:04.150 I am happy to be on the front row and happy because the bike is working well and feels good to ride. I didn’t have any big problems today, just a small problem with the front tyre feel. But apart from that, nothing of note. I am looking forward to the race tomorrow and I think I can make the podium for sure. I hope to get a good start, fight at the front of the pack and be in a good position at the end. The important thing for me is to make sure I score a good number of points and maintain my championship lead. Final qualifying 1 Roberts (Aus-Ducati) 2:03.685, 2 Pirro (I-Yamaha) 2:03.924, 3 Berger (F-Honda) 2:03.929, 4 Xavi Simeon (B-Alstare Suzuki) 2:04.150, 5 Corti (I-Yamaha) 2:04.156, 6 Antonelli (I-Honda) 2:04.601, More, from a press release issued by HANNspree Ten Kate Honda: Kiyonari shines in Superpole qualifying Ryuichi Kiyonari was the HANNspree Ten Kate Honda Superbike team’s highlight of the day and set a blistering performance in the Superpole Qualifying this afternoon. He impressively worked his way forward after concluding the morning’s second qualifying session in sixteenth place. In what was easily his best qualifying performance to date, Kiyonari was the first man to start the one-lap race against the clock and pushed hard on his Honda CBR1000RR to set the time to be beaten at 1’59.318. It took seven riders before the time was crushed, firstly by Michel Fabrizio, then followed by Troy Corser and eventual pole-sitter Troy Bayliss. It was Max Biaggi who robbed Kiyonari of his first ever WSB front row start. A satisfied Kiyonari will now start tomorrow’s race from fifth place on the grid, his best position so far this season. Carlos Checa took a total reversal of fortune. After concluding the morning’s second qualifying practice in ninth position he didn’t succeed to improve in his Superpole lap and was eventually sent back to a fourth row start. Kenan Sofuoglu finished the second qualifying practice in a disappointing twenty-sixth position and did not qualify for Superpole. Carlos Checa, 1’59.587; “Today has been a poor day of qualifying for me. We are not far off the pace and have been able to stay consistent but I couldn’t set that single fast lap.” “My Superpole lap was far from good, I experienced a lot of rear chatter and lost valuable time. I will need a good start tomorrow and work towards a good position in the first laps and start the race from that point. It is a handicap having to start from the fourth row on the grid and not a position to win the race.” Ryuichi Kiyonari, 1’59.318; “I am very happy with my Superpole lap. I qualified sixteenth and made my way up to fifth place on the grid. That’s a big jump as I’m normally not strong in the one lap attack.” “My feeling with the machine and the tyres was good today on my best lap. We tried a different setting today and the feeling was improving throughout the sessions The pace is good but still not fast enough. I’ll try and make a good start tomorrow and then find the connection with the fast group and work from there. I’ll need to push hard in the first laps for a good result.” Kenan Sofuoglu, 2’01.302 (QP2); “It was quite a disappointing session for me today as we were expecting an improvement but it just didn’t work. I tried to watch other riders on their laps but just can’t seem to adapt to riding the big Superbike.” “The team have worked very hard but it hasn’t paid off so far and we are now past the mid-season mark. I hope we can make some improvement tomorrow to give some motivation to everybody in the team. Like every Saturday night I’m hoping for a better result on Sunday.” More, from a press release issued by Troy Corser’s publicist: TROY MISSES SUPERPOLE VICTORY BY A WHISKER! Troy missed his chance of notching up Superpole victory number forty-three by the narrowest of margins in Brno this afternoon. At the end, fellow countryman Troy Bayliss (Ducati) took Superpole, with a lap of 1:58.345 – a tenth of a second quicker. Apart from Troy’s Yamaha, the front row of the grid is an all Ducati affair, with Michel Fabrizio third and Max Biaggi fourth. Troy – 2nd, 1:58.451 I am pretty happy with how the weekend has gone so far and happy to be mixing it with all those Ducatis. I think the last three of four races have been good for us and the bike is working very well. The grip here has been improving throughout the weekend and I think it’s going to be as good, if not better, tomorrow. I had a bit of an unfortunate crash this morning and hurt my right shoulder a bit. It’s a bit sore, but it isn’t a problem when I’m on the bike and I don’t expect it to hold me back tomorrow. We had changed the front end geometry a bit to get more stability and to allow me to brake harder. After one lap, I tried to brake a bit later in one corner and down I went. I tumbled into the gravel trap and got hit by my bike and that’s what made my shoulder sore. I guess I was lucky that I didn’t hurt myself badly. But, we learnt something from the experience and that’s good. I feel we have quite a good set-up for the race and the tyres are consistent. I hope the weather stays dry and we can put on a good show for the fans. More, from a press release issued by Team Pedercini: Team Pedercini enters the Superpole for its forth time in this season. Aytron Badovini succeeded to be in the top sixteen, getting the possibility to run the quick lap. Today’s result satisfies both the team and the riders who is going to start from the 4th line hunting for points in tomorrow’s race. Same goal for Vittorio Iannuzzo who is improving round by round recovering from the bad injury of the season begin. The rider from Campania reached a good pace which allows him to feel confident about getting his first seasonal points tomorrow. On the other hand, the young riders of the Supertsock ran up against an harder qualifying. Yoann Tiberio is going to start from the sixth line while Alessio Aldrovandi from the seventh one. Both the riders are going to spend the warm-up fine-tuning the bike, testing a different balance in order to reverse the bad trend. VITTORIO IANNUZZO | Kawasaki ZX-10R | 25th classified in 2’01.214: “I have improved respect to Misano although I still cannot do my best when I need to push by using the soft tyre. That influences my starting position which I wished to be better especially with a view to the race. Anyway my pace is pretty good and passing is not impossible on this track so my goal is always the same: finishing the race in the top-15″. AYRTON BADOVINI | Kawasaki ZX-10R |16th classified in 2’01.161: “I’m pretty satisfied with running the Superpole once again and above all to be in a good form for tomorrow’s race which I hope to finish in the points. We have found a good setting which allows me to ride effectively without damaging the tyres too much, that might be crucial in the second part of the race”.

Updated: Parkes On World Supersport Pole Position In The Czech Republic

0

FIM Supersport World Championship Brno, Czech Republic July 19, 2008 Final Qualifying Results (all on Pirelli tires): 1. Broc PARKES (Yamaha YZF-R6) 2:03.203 2. Barry VENEMAN (Suzuki GSX-R600), 2:03.452 3. Josh BROOKES (Honda CBR600RR), 2:03.562 4. Andrew PITT (Honda CBR600RR), 2:03.590 5. Craig JONES (Honda CBR600RR), 2:03.761 6. Mark AITCHISON (Triumph Daytona 675), 2:03.775 7. Jonathan REA (Honda CBR600RR), 2:03.934 8. Vesa KALLIO (Honda CBR600RR), 2:04.135 9. Matthieu LAGRIVE (Honda CBR600RR), 2:04.368 10. Russel HOLLAND (Honda CBR600RR), 2:04.508 11. Gianluca NANNELLI (Honda CBR600RR), 2:04.546 12. Didier VAN KEYMEULEN (Suzuki GSX-R600), 2:04.605 13. Gregory LEBLANC (Honda CBR600RR), 2:04.670 14. Robbin HARMS (Honda CBR600RR), 2:04.676 15. Garry MCCOY (Triumph Daytona 675), 2:04.721 16. David SALOM (Yamaha YZF-R6), 2:04.779 17. Joan LASCORZ (Honda CBR600RR), 2:04.887 18. Massimo ROCCOLI (Yamaha YZF-R6), 2:04.891 19. Ivan CLEMENTI (Triumph Daytona 675), 2:04.903 20. Gianluca VIZZIELLO (Honda CBR600RR), 2:04.910 21. Chris WALKER (Kawasaki ZX-6R), 2:05.115 22. Fabien FORET (Yamaha YZF-R6), 2:05.151 23. Katsuaki FUJIWARA (Kawasaki ZX-6R), 2:05.328 24. Danilo DELL’OMO (Honda CBR600RR), 2:05.507 25. Graeme GOWLAND (Honda CBR600RR), 2:05.775 More, from a press release issued by Triumph Italia Be1 Racing: Triumph Italia Be1 Racing comes really close to the first row with Mark Aitchison. The young Aussie records the sixth best time after the second timed session at Brno, just one tenth slower than the former champion Andrew Pitt and his factory Honda. Aitchison has been really quick during the whole session, lapping several times close to his best time; that allows the rider and the team to feel confident for tomorrow’s race with the goal to improve the sixth final place taken fifteen days ago at Misano. On the other hand, Ivan Clementi is going to start form the fifth line. The Italian rider was not able to fix the rear chattering of his bike and that prevented him from getting a better result on a track which usually suits his riding style. MARK AITCHISON | Triumph 675 | 6th best time in 2’03.775: “I would have had the chance to start from the first line but I paid for my lack of experience and I was not able to improve my time further. We found a good setting this morning, then we focused on choosing the best kind of tyres for the race. I recorded my best time during a series of very quick laps; that is really good and I feel confident to be one of the best riders of tomorrow’s race”. IVAN CLEMENTI | Triumph 675 | 19th best time in 2’04.903: “My problem is linked with just two corners where I collect the most of the gap from the bests. I cannot find the right set-up for the fork in order to remove the chattering. Tomorrow morning we will test a different balancing for the bike in order to get a better control which can lead to improve my times”. More, from a press release issued by HANNspree Ten Kate Honda: Pitt starts Brno Supersport race from front row HANNspree Ten Kate Honda rider Andrew Pitt secured a front row start in the second day of qualifying in Brno. Pitt set the fastest time in his first lap of the afternoon’s official practice and looked likely to claim his third pole of the season. He focused for the remainder of the session on finding the right tyres and didn’t manage to further improve his fastest time of 2’03.590 0.387s behind pole sitter Broc Parkes. Pitt, who is looking for a continuation of his winning streak, will start Sunday’s race from fourth place on the grid. Jonathan Rea has adapted himself quickly to the new track and topped the time sheets in the morning’s free practice session. In the official practice Rea maintained his pace and secured a second row start in a best time of 2’03.934, the seventh fastest qualifying time. Both riders are confident with their race pace and set-up and aim to convert their starting positions into a top finish for the team. Andrew Pitt, 2’03.590; “I am pretty happy to be on the front row. We probably had pole there for a while and luckily we stayed on the front row. We wanted to come through on the tyre choice and stayed out there and didn’t come back in to put new tyres in again.” “We found the best combination with the tyres and Johnny and I are in a good position to be really strong in the race. I’m looking forward to racing tomorrow.” Jonathan Rea, 2’03.934; “For me the qualifying sessions today were ok. I looked at the race pace of the other riders and we are right in the ball park. I put some race laps together in the session and concentrated on the race set-up.” “We have a good set-up for tomorrow and I’m confident with my tyre choice. I am really looking forward to the race, we have the pace to do well and I’m really confident. I just hope from row two I can make a good start and be there from lap one and challenge the fight for a race.” More, from a press release issued by Scuderia Triumph-SC: GARRY McCOY INJURED IN PRACTICE SESSION AT BRNO (Brno Czech Republic 2008, July 19) The main event of the second practice day at Brno Automotodrom for Triumph-SC Team has been the very bad accident occurred to Garry McCoy during the second free practice session in the morning. About ten minutes to the finish Garry, who was running very fast, so that at first split he recorded the fourth fastest, found on his line outing a corner in the downhill sector, the Pitt’s Honda running slowly along the track edge. McCoy, heavy engaged to grab a fast lap, tried to spare the unexpected obstacle, but he touched with the front brake lever to Honda’s back. The 675 Daytona of the veteran Aussie has been throw to the protections along the track. The crash has been very hard, the bike front has been disintegrated while Garry crashed against the wall with the left part of his back. Broken ribs and a heavy internal thoracic trauma. The rider was conscious, able to manage the action of first aid rescue along the track. After the first control by Clinica Mobile people McCoy has been translated by medical helicopter to Úrazová Nemocnice Hospital in Brno-Trnitá for more controls to verify the presence of injuries at lung and pleura level. The following controls did show also a fracture at the sixth loin vertebra, without any damage at neurological level, as well a left lung contusion, so Garry has been transported, following his request, to Private Klinik in Wien, where an orthopaedic specialist well known by Garry is working. Ruggero Scambia clearly increased his performance, as well the grid position did not change too much: “I increased more as 3 seconds my lap time, but that wasn’t enough and I remained in the back of the grid. But now the gap from most of my rivals is possible to manage and if I’ll have a good start I could look for a result able to give me trust for next events.” No glory in 600 Superstok race for Robbie Stewart, 25th at the finish after a bad start that put him il the last position at the end of the first lap: “I don’t know how to say, the bike runs well, but i had a slow start and then I was not able to have a good pace. Just in the final laps I started to ride better, but it was too late.” More, from a press release issued by Yamaha Racing: Parkes takes fifth pole position in a row Broc Parkes consistently brilliant performances in qualifying in the 2008 season continued at the Brno meeting when he took a remarkable fifth consecutive pole position. His pre-race successes at Assen, Monza, Nürburgring and Misano grew to five after Parkes scored a 2’03.203 second lap towards the end of a busy afternoon session. Parkes’ lap was a new absolute track best, on a circuit which had been resurfaced earlier in the season. The expected rains stayed away during the second day of track action, allowing Parkes to lead Barry Veneman, Josh Brookes and Andrew Pitt on the front row of the grid. Fabien Foret is recovering from a day one crash that saw him crack his C6 and C7 vertebrae, and suffer a concussion. Latest medical reports indicate that Foret will be out of action for two months, but should make a full recovery. Massimo Roccoli (Yamaha Team Italia Lorenzini by Leoni) slipped one place to 18th on the grid on day two of qualifying and David Salom (Yamaha Spain World Supersport) went 16th. Broc Parkes (1st – 2’03.203 – Yamaha World Supersport Team) “It’s a great feeling to have had five pole position rides in a row and I’m happy with the final results of all the work we did in qualifying. Our bike is working really well on fresh rubber, as usual. I think that the rate of wear from the tyres will be the same for everyone in the race tomorrow, and the pace will be pretty even between the top guys. Maybe it will be a case of managing the tyres in the last few laps. But on the new track surface, we’ll have to wait and see.” Wilco Zeelenberg (Team Manager, Yamaha World Supersport Team) “Broc is simply brilliant at getting pole positions and five in a row is really something special. What can we say, qualifying fastest is what he is really good at right now and the desire to succeed is also in his guts at the moment. He kept his patience to wait until we got to know all the information we needed for the race, even though another rider went faster near the end. Only then did Broc go out and take pole. That is the best thing about his practice performances, his willingness to work for a good race set-up.” Massimo Roccoli (18th – 2’04.891 seconds – Yamaha Team Italia Lorenzini by Leoni) “Today wasn’t a good day because although the bike was very good, the engine has had another step of evolution and was very competitive, I didn’t ride as aggressively as I needed to. Our tyre strategy was excellent but I think it is simply a problem of my confidence to go as fast as I know I can.” David Salom: (16th – 2’04.779 seconds – Yamaha Spain) “I’ve been riding very comfortably and the faster I went the more comfortable I felt. My best lap time is very good, faster than last year’s pole position. I’ve improved my best time from last year by three seconds and the bike, team and me have all improved too.”

Biaggi Tops Second World Superbike Qualifying Session At Brno

0

FIM Superbike World Championship Brno, Czech Republic July 19, 2008 Qualifying Results (before Superpole, all on Pirelli tires): 1. Max BIAGGI (Ducati 1098 RS08), 1:58.965 2. Jakub SMRZ (Ducati 1098 RS08), 1:59.125 3. Troy BAYLISS (Ducati 1098 F08), 1:59.166 4. Max NEUKIRCHNER (Suzuki GSX-R1000), 1:59.250 5. Fonsi NIETO (Suzuki GSX-R1000), 1:59.357 6. Troy CORSER (Yamaha YZF-R1), 1:59.380 7. Michel FABRIZIO (Ducati 1098 F08), 1:59.482 8. Niccolo CANEPA (Ducati 1098 F08), 1:59.634 9. Carlos CHECA (Honda CBR1000RR), 1:59.648 10. Yukio KAGAYAMA (Suzuki GSX-R1000), 1:59.708 11. Ruben XAUS (Ducati 1098 RS08), 1:59.846 12. Lorenzo LANZI (Ducati 1098 RS08), 1:59.850 13. Noriyuki HAGA (Yamaha YZF-R1), 1:59.913 14. Karl MUGGERIDGE (Honda CBR1000RR), 1:59.944 15. Ayrton BADOVINI (Kawasaki ZX-10R), 2:00.221 16. Ryuichi KIYONARI (Honda CBR1000RR), 2:00.225 17. David CHECA (Yamaha YZF-R1), 2:00.228 18. Shinichi NAKATOMI (Yamaha YZF-R1), 2:00.232 19. Gregorio LAVILLA (Honda CBR1000RR), 2:00.304 20. Roberto ROLFO (Honda CBR1000RR), 2:00.374 21. Regis LACONI (Kawasaki ZX-10R), 2:00.482 22. Makoto TAMADA (Kawasaki ZX-10R), 2:00.641 23. Shuhei AOYAMA (Honda CBR1000RR), 2:00.905 24. Sebastien GIMBERT (Yamaha YZF-R1), 2:01.059 25. Vittorio IANNUZZO (Kawasaki ZX-10R), 2:01.214 26. Kenan SOFUOGLU (Honda CBR1000RR), 2:01.302 27. Jiri DRASDAK (Honda CBR1000RR), 2:02.373 28. Christian ZAISER (Yamaha YZF-R1), 2:03.118 29. Jason PRIDMORE (Honda CBR1000RR), 2:03.397 30. Milos CIHAK (Suzuki GSX-R1000), 2:03.758

Crutchlow Grabs British Superbike Pole Position At Oulton Park

Cal Crutchlow powered his HM Plant Honda to pole start for the seventh round of the Bennetts British Superbike Championship at Oulton Park and promised to convert his pace into a winning double to steel his chances of reeling in Shane Byrne in the title stakes. The Coventry rider enjoys riding the Cheshire circuit, having taken pole in the earlier visit there back in May then in the races he had mixed fortunes with a sixth place and then a tumble but this time around Crutchlow is determined to show what might have been. “I’m looking forward to getting back out there in the races and am keen to make amends for what happened here earlier on believe me, I will be giving it everything out there,” said Crutchlow after his success in the Swan Combi 50 Roll for Pole. His pole setting lap came in 1m 36.298secs, an average speed of 100.63mph, and it might have been better. “I was baulked a bit on one lap and it was very windy out there, a bit dodgy in places, so it might have been faster, but it is good to be back on top. Now I hope to turn this into two race wins I’ve got to go for it here, it’s my favourite circuit so really there is nothing else but achieving that.” Crutchlow, one of only three riders to have beaten the dominant Byrne so far this term, starts the races with a 97 points deficit on the Airwaves Ducati rider in the standings. There is only 0.292 seconds between them at the top of the leaderboard, with Byrne confident that he can repeat his winning double of that first visit here. Tom Sykes joined them at the front of the grid, powering his Rizla Suzuki to a 1m 36.591secs lap of this 2.692 mile circuit, just 0.001secs down on Byrne but a quarter of a second up on Leon Haslam, riding the second HM Plant bike, who completed the front row. Karl Harris, the Rob Mac Racing Yamaha, who had set the pace through Friday’s free practice ran fifth best, though within half a second of Crutchlow, to nudge Simon Andrews, aboard the Lloyds British Jentin Yamaha back a place on a second row that also included Mallory Park race winner Michael Rutter on the North West 200 Ducati and James Ellison on the Hydrex Bike Animal Honda. Tristan Palmer continued his strong performances, running ninth fastest on the Tena for Men Honda ahead of Billy McConnell, the MSS Discovery Kawasaki rider who escaped injury in a tumble. Scott Smart, riding Hawk Kawasaki, joined them on the third row together with Gary Mason, the fastest of the Daily Star Cup contenders, aboard the Quay Garage Honda. Cup leader John Laverty ran second in class on the Buildbase NW200 Ducati ahead of Riders Honda’s Martin Jessopp and Chris Burns aboard the STP MV Agusta. Leading qualifying times: 1. Cal Crutchlow (HM Plant Honda) 1:36.298s 2. Shane Byrne (Airwaves Ducati) +0.292s 3. Tom Sykes (Rizla Suzuki) +0.292s 4. Leon Haslam (HM Plant Honda) +0.523s 5. Karl Harris (Rob Mac Racing Yamaha) +0.533s 6. Simon Andrews (Lloyds British Yamaha) +0.807s 7. Michael Rutter (North West 200 Ducati) +1.073s 8. James Ellison (Hydrex Bike Animal Honda) +1.260s 9. Tristan Palmer (TENA for Men Honda) +1.502s 10. Billy McConnell (MSS Discovery Kawasaki) +1.542s More, from a press release issued by Team Suzuki News Service: Rizla Suzuki’s Tom Sykes took a hard-fought third place at Oulton Park for round seven of the Bennetts British Superbike Championship while his team-mate Atsushi Watanabe came home in 13th position. The 50-minute qualifying session started off in damp conditions but the 2.69-mile Cheshire circuit dried rapidly. Sykes was always in contention for pole position and led the time-sheets for much of the session, showing he has real race-winning pace. Watanabe used his previous experience at Oulton Park to maintain his top 15 placing and will be aiming for a top-10 finish when the racing starts in anger. Race one will take place at 1315 on Sunday and race two at 1630. Tom Sykes: “I think I could have been a little further up if I hadn’t been caught up in traffic at the end of the session but third place and the front row of the grid is fine as I know I can get away well. During free practice we worked our way through a number of wet settings and we have made some progress getting the bike nicely balanced for racing in the rain if it comes tomorrow. “In the dry there is still a bit of work to be done as the front end is feeling a little vague at a couple of corners and I want the bike to be doing the work rather than me. I can put in consistent 1min 36s which is a good race pace so I feel confident ahead of tomorrow’s races.” Atsushi Watanabe: “I am happy I have improved since last Oulton Park. My lap times are better and my feeling for the track. My Rizla Suzuki technicians worked hard on rear settings to improve how my bike feels as it had a lot of movement. I want a good finish tomorrow for me and my team.” Pete Jennings – Crew Chief: “Tom did get baulked towards the end of the session which was a shame but his race pace is good, and we have a few little changes to make ahead of race day which we will evaluate during warm-up.” Qualifying results: 1: Cal Crutchlow (Honda) 1:36.298 2: Shane Byrne (Ducati) +0.292 3: Tom Sykes (Rizla Suzuki) +0.293 4: Leon Haslam (Honda) +0.523 5: Karl Harris (Yamaha) +0.533 6: Simon Andrews (Yamaha) +0.807 7: Michael Rutter (Ducati) +1.073 8: James Ellison (Honda) +1.260 9: Tristan Palmer (Honda) +1.502 10: Billy McConnell (Kawasaki) +1.542 13: Atsushi Watanabe (Rizla Suzuki) +1.754 More, from a press release issued by GSE Racing/Airwaves Ducati: BYRNE ON THE FRONT ROW FOR AIRWAVES DUCATI Airwaves Ducati rider Shane Byrne will start on the front row for round 7 of the British Superbike Championship. Shane achieved the 2nd fastest time in qualifying at Oulton Park today. Team mate Leon Camier will start from row 8. After a wet practice session in the morning, which both Airwaves Ducati riders decided to sit out, qualifying was to remain dry for the full 50 minutes. Shane pushed hard throughout the session and his fastest lap time of 1:36.590 came on lap 22 of 24. Continuing his run of starting on the front row for every race so far this season, Shane said: “I’m really happy to have secured a front row start for Airwaves Ducati. I was stuck behind traffic on my fastest lap and my final corner was sacrificed by not being able to take my normal line. I had one last chance to try and grab pole but the wind just caught me out on the first corner. But I can’t complain with second. If warm-up tomorrow morning is dry there are a few slight changes that I would like to try on the Airwaves Ducati, but if not, I’m confident that the races should bring us some good results, and importantly more championship points.” Qualifying came to a premature end for Leon when 15 minutes into the session and on his 5th lap he came off at Island bend. As he took no further part in the qualifying session, Leon was unable to better his time of 1:41.644 and so will start tomorrow’s races from 29th on the grid. Following qualifying, Airwaves Ducati Team Manager Colin Wright commented, “Leon had been doing a good job so far this weekend and he felt confident going into qualifying. The session started as planned and he was looking to get into a good rhythm but unfortunately he slipped off. Physically Leon is OK but he did take a heavy fall and he is unsure as to the reason for the crash. We will assess his condition in the morning and decide if he is fit to race.” Qualifying Result: 1. Cal Crutchlow HM Plant Honda 1:36.298 2. Shane Byrne – Airwaves Ducati 1:36.590 3. Tom Sykes Rizla Suzuki 1:36.591 4. Leon Haslam HM Plant Honda 1:36.821

Updated Again: Saturday Morning AMA Superbike Practice At Laguna Seca Cancelled Due To Fog

The 40-minute AMA Superbike practice session scheduled for Saturday morning at Mazda Raceway Laguna Seca has been canceled due to fog and limited visibility and will not be rescheduled, according to AMA Superbike Media Relations Manager Eric Putter.

The session was the only practice session scheduled for the AMA Superbike class Saturday and would have been their second of two on the weekend.

The AMA Superbike practice will not be rescheduled due to the FIM MotoGP World Championship schedule taking priority this weekend.

AMA Superbike is scheduled to have a 25-minute qualifying session Sunday morning, prior to a 28-lap race at 3:45 p.m. local time Sunday afternoon.

Update: Saturday’s AMA Superbike practice may be rescheduled from 5:15 to 5:45 p.m. local time, according to AMA Pro Racing’s Bill Syfan. “Our friends with FIM, Dorna and the track are working on making that time available to us,” said Syfan. “We are working it out. We polled the teams about the possibility of the 5:15 session, and they were pretty positive about it.”

“Anytime you schedule a session at 8:00 a.m. at Laguna Seca you never know what you’re going to get,” said six-time AMA Superbike Champion Mat Mladin. Mladin, who agreed that it was too foggy to ride, said the session at 5:15 p.m. Saturday could end up being more productive because it will be closer to the actual time of day of the race.

Second Update: Saturday’s AMA Superbike practice has officially been rescheduled for 5:15 to 5:45 p.m. Saturday.

Updated: Bruce Rossmeyer’s Daytona Racing On Pole Position For SunTrust MOTO-ST Race At Barber

Barber SunTrust MOTO-ST 500K Barber Motorsports Park Birmingham, Alabama July 19, 2008 Qualifying Results (all on Pirelli tires): 1. Bruce Rossmeyer’s Daytona Racing (Shawn Higbee/Mike Smith), Buell 1125R, SuperSport Twins, 1:32.040 2. Touring Sport Ducati 75 (Ryan Gordon/Ryan Elleby/Frank Shockley), Ducati 848, SuperSport Twins, 1:32.313 3. Aprilia USA 1/Lloyd Brothers Motorsports (Ty Howard/Mike Himmelsbach/Zac Chapman), Aprilia RSV1000, SuperSport Twins, 1:33.035 4. Aprilia USA 6/Lloyd Brothers Motorsports (Henry Wiles/Zac Chapman/Ty Howard), Aprilia RSV1000, SuperSport Twins, 1:33.354 5. CrozierMotorsports.com (Mark Crozier/Nathan Dressman), Ducati 848, SuperSport Twins, 1:33.951 6. National Precious Metals (Marco Martinez/Calvin Martinez), Ducati 848, SuperSport Twins, 1:35.145 7. Rightsforbikers.com (Justin Filice/Armando Ferrer/Rodolfo Ramirez), Ducati PS1000LE, Grand Sport Twins, 1:35.536 8. Team Hooters Aprilia (Andy Deatherage/Ben Carlson/Mike Luke), Aprilia RSV1000, SuperSport Twins, 1:35.615 9. Touring Sport Ducati 77 (Pete Friedland/Brad Phillips/Frank Shockley), Ducati PS1000LE, Grand Sport Twins, 1:36.792 10. M4 AVTEQ Racing 66 (Dane Westby/Kyle Martin/Russell Wikle), Suzuki SV650, Sport Twins, 1:36.994 More, from a press release issued by MOTO-ST: > Higbee fastest in SunTrust MOTO-ST qualifying at Barber Motorsports Park BIRMINGHAM, Ala. (July 19, 2008) Shawn Higbee earned his second consecutive SunTrust MOTO-ST Series pole position on Saturday morning, when he posted the fastest time during qualifying in advance of Sunday’s Barber 500K at Barber Motorsports Park. The Oconomowoc, Wis. racer converted his ‘Destination Daytona Pole Award’ into a Buell Motorcycle Company Super Sport Twins (SST) class victory in early June at the MOTO-ST event in Elkhart Lake, Wisconsin, and is hoping for a repeat performance on Sunday at the scenic Barber circuit, located near Birmingham, Ala. Higbee’s No. 8 Bruce Rossmeyer’s Daytona Racing Buell 1125R lapped the 17-turn, 2.38-mile road course in 1 minute and 32.040 seconds, at an average speed of 89.960 mph. The effort was more than a quarter of a second better than that of second-fastest qualifier, Ryan Gordon of Clemson, S.C., whose No. 75 Touring Sport Ducati 848 posted a lap of 1:32.313 (89.694 mph). Saturday’s schedule consisted of a 90-minute practice session, which was immediately followed by a 10-minute break and the 20-minute qualifying session. Higbee was pleased with the result and with the way his team tweaked the No. 8 Buell during the limited track time. “Our practice time was cut a little short because we came in and swapped shocks on the bike. We wanted to come in and make some changes,” said Higbee, who took part in an AMA race at Barber several years ago. “I think tire conservation is going to be a big part of the race; it’s so hot that the track is really hard on tires. The bike is oversteering a bit right now, so we might make some changes to try to improve it”¦ or else we’ll be out there flat-tracking it.” Asked about the significance of starting up front on Sunday, Higbee deadpanned, “It’s just a pole position, but hopefully it’s a good indication of how things will go in the race tomorrow. It’s going to be interesting. We feel like we’ve got a bit of momentum going after our win at Road America.” On Sunday, Higbee will be teamed with Mike Smith of Canton, Ga. Ryan Gordon will start Sunday’s Barber 500K from the second position. The No. 75 Touring Sport Ducati team earned runner-up finishes in the season’s first two races (at Daytona and Virginia) and are hoping to get back on form following a fourth-place showing in Round 3 at Road America. Gordon is teamed with Ryan Elleby (Powder Springs, Ga.) and Frank Shockley (Greenville, S.C.). Ty Howard of Weatherford, Texas will line up third on Sunday on the No. 1 Aprilia USA / Lloyd Brothers Motorsports Aprilia Tuono 1000R. Howard is pleased with his spot considering today’s practice and qualifying sessions were the first time this particular bike has been pushed to the limit on the racetrack. “We struggled out there a little bit; we don’t quite have the right setup yet,” said Howard, whose team enters the weekend as the series’ points leader on the strength of wins in the first two rounds. “With just one practice session and the time split between two riders [teammate Mike Himmelsbach of Quakertown, Pennsylvania] it makes it hard to get the setup dialed in. Going into qualifying we weren’t sure about how fast our setup was”¦ and it wasn’t. We just worked through it and it’s also the first time this bike has really been ridden at race pace, so we know we have some stuff to do for tomorrow.” The No. 6 Aprilia USA / Lloyd Brothers Motorsports Aprilia Tuono 1000R will start fourth on Sunday (ridden by Zac Chapman of Weatherford, Texas and Henry Wiles of Blanchard, Mich.) in front of the No. 55 Crozier Motorsports Ducati 848 (ridden by Mark Crozier of Fort Valley, Ga. and Nathan Dressman of Clarkston, Mich.). Leading the way in BMW GrandSport Twins (GST) class qualifying on Saturday was Justin Filice on the No. 59 RightsForBikers.com Ducati PS 1000LE. The Modesto, Calif. racer lapped the Barber circuit in a time of 1:35.536 (86.668 mph), which was seventh fastest overall of the 25 teams (in the three divisions) that took to the track during qualifying. Filice set his fast time on the team’s 10th and final qualifying lap of the session. “On that last lap, I was behind one of the ST bikes and my tires were starting to go off and get a little slippery, so I backed it off a little. Then one of the ST bikes went around me and I said, ‘I’ll give it another shot,’ and followed him around for a little bit and ended up clicking off a [one minute and] 35.5. My team didn’t even tell me until I came into the pits.” Filice feels comfortable heading into Sunday’s Barber 500K. “I’m riding with Armando Ferrer and Rodolfo Ramirez. They both did a great job today, getting down into the [one minute and] 37s, I believe. I think we’re going to be very competitive tomorrow. I’m going to start and try to get a little bit of a gap. The plan is for them to maintain and I’ll ride the last 40 minutes or so.” The No. 77 Touring Sport Ducati PS 1000LE (ridden by Pete Friedland of Columbia, S.C., Brad Phillips of Greer, S.C. and Frank Shockley of Greenville, S.C.) was second fastest of the GST teams during qualifying, ahead of the No. 23 Motocorse Bimota DB5 of Chris Boy (Ft. Lauderdale, Fla.), Greg Melka (Tampa, Fla.) and Kevin Mendez (Davie, Fla.). The No. 66 M4 AVTEQ Suzuki SV650 was the class of the field in the Sport Twins (ST) division during qualifying. Rider Dane Westby of Tulsa, Okla. toured the Barber circuit in 1:36.994 (85.366 mph). Westby heads into Sunday’s feature race with an open mind, in terms of strategy. “I’m not really sure what our plan is; I’m just getting on it and riding it until they tell me to get off.” The points-leading No. 9 Pair-A-Nines Kawasaki EX650 of Jimmy Filice (Daytona Beach, Fla.) and Jay Springsteen (Lapeer, Mich.) were the next-fastest of the ST qualifiers, timing in at 1:38.432 (84.119 mph). Behind them were the No. 67 M4 AVTEQ Suzuki SV650 of Ryan O’Donnell (Dallas, Texas) and Russ Wikle (Huntsville, Ala.). The Barber 500K gets the green flag at 8:00 a.m. Sunday morning. The race is scheduled for two hours and thirty minutes. The SunTrust MOTO-ST Series is organized and sanctioned by Professional Motorsports Productions (PMP) of Toronto, Ontario, Canada and the Grand American Road Racing Association, based in Daytona Beach, Fla., provides the series with administrative and commercial support. Learn more about MOTO-ST at www.moto-st.com.

2009 AMA Pro Racing Daytona Superbike Rules

Daytona Superbike Equipment Regulations All machines eligible for participation in Daytona Superbike must be approved by AMA Pro Racing and homologated by the manufacturer or sanctioning body. Machines currently eligible for homologation by their manufacturer or distributor for competition in 2009 are: Aprilia Tuono BMW HP2 Sport Buell 1125R Ducati 848 Ducati S4R Honda CBR600RR Kawasaki Ninja ZX-6R KTM Super Duke MV Brutale 910S Suzuki GSX-R600 Triumph Daytona 675 Yamaha YZF-R6 Each homologated machine will have a published Technical Information Form (TIF) containing the AMA approved specifications required for competition. Specifications will include, but not be limited to make, model, year, original displacement, and special allowances (if any) for this specific homologated machine. The original TIF may be modified to enhance or reduce the performance of the machine based upon actual competition experience. Unless otherwise specified, all parts must originate from the same make/model as the homologated machine, meaning no up-dating or back-dating is permitted 1. HORSEPOWER AND WEIGHT LIMITS A. Minimum weight is 360 lbs in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. B. Once the machine weight has been established, the motorcycle will be tested for power output on the official series dynamometer. Power is limited to one (1) horsepower for every three (3) pounds of machine weight, up to a maximum of 140 horsepower. Fuel may be added to allow for the dynamometer testing after the official weight has been recorded. C. In no case may more than 25 lbs of ballast be added to any machine, said ballast to be added/fastened in accordance with approved mounting procedures. D. If necessary, specific motorcycles may be allowed a variance from the standard power to weight ratio to ensure parity in competition. Where such variances are allowed, they will be published on the TIF for the machines affected. E. Combined motorcycle and rider weights will be used to determine power limits starting in the 2010 season. 2. TIRES A. XXXXXX is the Official Tire of AMA Pro Road Racing and only tires produced by XXXX and mounted at the meet may be used in competition. B. The number of available compounds, configurations, and quantities available for use at each event will be announced coincident with the announcement of the Official Tire of the series and may be altered during the course of the 2009 season per safety, wear and related experience. 3. FUEL A. Official Fuel – The Official Fuel of AMA Pro Racing is XXXXXXXX and its exclusive use in unadulterated form shall be mandatory. B. Only air may be mixed with the fuel as an oxidant, and no other substances, chemicals and/or liquids whatsoever shall be added, combined, mixed and/or introduced to said Official Fuel whether intentionally or unintentionally unless approved in advance in writing by the AMA for use by all competitors. C. All competitors must use the official fuel, as supplied by the manufacturer at the track, during all on-track sessions. D. All motorcycles must prominently display the appropriate unmodified official fuel company decal on the motorcycle at all times. E. AMA Pro Racing has the right to sample a competitor’s fuel at any time. F. Competitors are responsible for the safe and proper handling and security of their fuel from when it is dispensed to them until it is used. G. Competitors are responsible for properly disposing of all unused fuel. 4. WHEELS/BRAKES A. Original equipment wheels must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. (1) Front wheels = 17″ x 3.5″ all machines (2) Rear wheels = 17″ x 5.5″ or 17″ x 6″ B. Original equipment brake calipers must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. C. Aftermarket brake pads and lines may be substituted by homologated units appearing on the Eligible Equipment List. D. The brake master cylinders may be substituted by homologated units appearing on the Eligible Equipment List. E. With approval of the Technical Inspector, front wheel spacers may be made “captive”. F. With approval of the Technical Inspector, rear wheel spacers may be made “captive”, and a caliper retaining device may be used. Chain adjuster must be OEM. 5. FRONT SUSPENSION A. Original front forks must be retained, including inner and outer tubes, fork bottoms, caliper mounts, axles and spacers. B. Aftermarket Cartridge kits appearing on the Eligible Equipment List are permitted and aftermarket fork caps may be substituted. C. A steering damper may be installed with a homologated unit appearing on the Eligible Equipment List. D. A fork brace may be installed with a homologated unit appearing on the Eligible Equipment List. E. Triple Clamps may be substituted with a homologated unit appearing on the Eligible Equipment List. F. Front suspension modifications are limited to: (1) Internal parts may be modified consistent and within the foregoing restrictions, including substitution of springs, change of shims and/or spacers, and addition of kit/aftermarket valving units appearing on the Eligible Equipment List. (2) External Compression Adjusters may be modified/changed. (3) Steering Head inserts to adjust rake may be used as long as no part of the frame is modified. 6. REAR SUSPENSION A. The original model, stock swingarm must be retained, unchanged, except that the axle adjustment opening/slot may be lengthened, with the permission of the Technical Inspector. B. The rear shock linkage may be substituted with a homologated unit appearing on the Eligible Equipment List. C. The rear shock may be modified or replaced by units appearing on the Eligible Equipment List. 7. FRAME/ADJUSTABLE PIVOT A. Unless otherwise provided for on the TIF, the original frame must be used. Unnecessary brackets may be removed. B. Adjustable swingarm pivots are permitted, but no modifications to the frame or swingarm can be made to allow this adjustability. 8. BODYWORK/CONTROLS/APPEARANCE A. Aftermarket, OEM-style bodywork and custom fairing mounts may be used. B. The fairing must match the shape of the OEM machine in silhouette and profile and the AMA shall have the right to use templates and go-no-go devices therefor. 1) An oil retaining, “sealed” lower fairing is mandatory. C. The stock gas tank must be used, but aftermarket gas caps are allowed. D. A front fender must be mounted. E. Aftermarket footpegs, clip-on bars, shift/brake mechanisms and fasteners may be used. F. Non-standard “Kill Switches” must not be spring loaded and must be well marked. G. Titanium Fasteners are not permitted. H. Tail sections may be increased in size to allow for required number display. Final approval rests with the Chief Technical Inspector. (1) AMA Pro retains the right to require number plates on machines with small or unusually sized or shaped tail sections. I. Numbers must be a minimum of 8 inches high and in a clear contrasting color to the background area on which they are displayed. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) No modifications are allowed except as follows: a. Cylinder head, cylinder and crankcase gasket surfaces only may be machined for increased compression. All other surfaces of the cylinder head, cylinder and crankcases must remain absolutely as homologated with no metal removal. b. Light cleaning of gasket surfaces with steel wool, Scotch-Brite®, etc. is permitted. Deburring radius of machined area must not be greater than 0.020 inches or 0.5mm. c. The cylinder head gasket may be changed. d. The valves, valve seats, guides, springs, tappets, oil seals, shims, cotter valve, spring base and spring retainers must be as originally produced by the manufacturer for the homologated machine. Valve spring shims are allowed. B. Camshaft (1) No modifications are allowed. (2) At the technical checks: for direct cam drive systems, the cam lobe lift is measured; for non direct cam drive systems (i.e. with rocker arms), the valve lift is measured. (3) The timing of the camshaft is free. C. Cam Sprockets (1) No dimensional modifications are allowed. (2) Cam sprockets may be slotted solely for the purpose of altering cam timing. (3) Press-on cam sprockets may be replaced with aftermarket steel bolt-on cam sprockets and adapters. (4) Aftermarket cam chain tensioners are permitted. D. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. E. Oil Pumps and Oil Lines (1) No pump modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. F. Connecting Rods (1) No modifications are allowed (including polishing and lightening). G. Pistons (1) No modifications are allowed (including polishing and lightening). H. Piston Rings (1) No modifications are allowed. I. Piston Pins and Clips (1) No modifications are allowed. J. Cylinders (1) No modifications are allowed except as provided for above. K. Crankcase and all other Engine Cases (i.e. ignition case, clutch case, etc.) (1) No modifications to the crankcases are allowed except as provided for above. (2) Lateral (side) covers may be altered, modified or replaced. If replaced, the cover must be made in material of same or higher specific weight and the total weight of the cover must not be less than the original one. (3) On motorcycles where lateral covers or engine cases contain oil, strengthened engine side covers or case guards must be installed. All such protection devices must weigh no less than the original homologated parts and must be approved by the AMA Pro Tech Inspector. L. Transmission/Gearbox (1) Kit-type Electronic “quick shifters” are allowed. (2) Manual “secondary” hand operated kill switch/quick shifters are not allowed. (3) Final drive system, if not by chain, may be modified to chain type, utilizing kits specified on the Eligible Equipment List. (4) Original equipment shift drum detent stars may be modified or replaced with approved, homologated aftermarket parts. (5) Other modifications to gearbox or selector mechanism are not allowed. M. Countershaft sprocket, rear wheel sprocket, chain pitch and size can be changed. (1) The sprocket cover can be modified. N. Stock carb bodies or stock fuel injection systems must be used, but carb internals, velocity stacks and injection management systems may be altered or replaced. O. Injectors must be stock and unaltered from the original specification and manufacture. P. Aftermarket exhaust systems appearing on the Eligible Equipment List may be installed. Q. “Dry Clutches” are only permitted when used on the equivalent OE production model. R. Aftermarket “Slipper” clutches appearing on the Eligible Equipment List are permitted. S. Homologated engine control unit (ECU), must be either: (1) As homologated and inner software can be changed; (2) Or the ECU kit model (produced and/or approved by the machine Manufacturer) can be used. (3) A special connector can be used to connect the kit ECU and the original wire loom. (4) Series provided Engine Control Units may be required in 2010 and beyond. 10. AIR BOX/INTAKE/SCOOPS A. Original equipment air box is required, without modification. B. An air filter is required. Original equipment air filter and air filters appearing on the Eligible Equipment List are permitted. C. Ram air systems are permitted if specified and used on the homologated motorcycle. Ducts and scoops, must be identical in specification to the original equipment system. 11. POST QUALIFYING/POST RACE TECH A. Immediately following each qualifying session or race, the top three finishers plus other motorcycles chosen at random at the discretion of the AMA will be tested on the Official Series Dynamometer to verify power. B. Other than the motorcycle’s throttle/twist grip, switches or any other device and/or methodology designed to and/or having the ability or potential to affect the horsepower readings during dynamometer testing are strictly prohibited. C. Any entrant, rider, crew member and/or entrant affiliate (who are not manufacturers of homologated motorcycles), who attempts to and/or does alter the performance of his/her/their machine following any competition event, in an effort to affect the dynamometer or weight results, will be disqualified from the meet and suspended from AMA Pro Road Racing participation for a period of no less than one year, and assessed a $50,000.00 fine which must be paid in full before reinstatement. A second offense will result in a lifetime ban for the offending entrant and/or entity. D. Any entrant, entrant affiliate and/or contractor who is/are manufacturers of homologated motorcycles, who attempts to and/or does alter the performance of its/their machine following any competition event, in an effort to affect the dynamometer or weight results, will be disqualified from the meet and suspended from AMA Pro Road Racing participation for a period of no less than one year, and assessed a $250,000.00 fine which must be paid in full before reinstatement. A second offense will result in a loss of approval for the homologated machine used in the meet where the offense took place, thereby rendering it ineligible for use by any and all entrants for a period of twelve (12) months. E. Machines unable to make post qualifying or post race tech and complete their dynamometer runs for any reasons, including major crashes or major mechanical failures will be penalized. Reasonable allowances may/will be made for minor mechanical failures that can be repaired, under strict supervision, in a reasonable amount of time and that do not have any bearing on performance or weight. Reasonable allowances may/will also be made for minor crashes on machines that can be ridden back to pit lane. Determination of ‘minor’ will be at the sole discretion of the Tech Inspector. F. In the instance where a motorcycle on the post-race dynamometer produces one run where that motorcycle registered within (but not more than) one horsepower in excess of the horsepower limit, that motorcycle will be re-tested at the end of that class/group, time allowing and at the request of the entrant. If that motorcycle again measures/tests any way in excess of the allowable horsepower limit , that machine will be penalized as per the Rule book. If that machine reads within the guidelines in the dynamometer re-do, no penalty will be assessed. G. Motorcycle weights will be checked immediately following qualifying or races, in the same condition in which they finish the activity, including all fluids such as oil, water and fuel. H. No fluid and/or any other item(s) may be added to the motorcycle prior to the determination of weight. Subsequent to official weight verification, fuel may be added for the purpose of completing the required dynamometer verification.

2009 AMA Pro Racing American Superbike Rules

All machines eligible for participation in American Superbike must be approved by AMA Pro Racing and homologated by the manufacturer or the sanctioning body. Each homologated machine will have a published Technical Information Form (TIF) containing the AMA approved specifications required for competition. Specifications will include, but not be limited to make, model, year, original displacement. The original TIF may be modified to enhance or reduce the performance of the machine based upon actual competition experience. Unless otherwise specified, all parts must originate from the same make/model as the homologated machine, meaning no up-dating or back-dating is permitted. 1. DISPLACEMENT CAPACITIES AND WEIGHT LIMITS A. Minimum weight is 370 lbs in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. B. Displacement capacities (1) 4 cylinders Over 600 cc up to 1000 cc 4-stroke (2) 3 cylinders Over 750 cc up to 1000cc 4-stroke (3) 2 cylinders Over 850 cc up to 1200 cc 4-stroke (4) The displacement capacities must remain at the homologated size. Modifying the bore and stroke to reach class limits is not allowed. 2. TIRES A. XXXXXX is the Official Tire of AMA Pro Road Racing and only tires produced by XXXX and mounted at the meet may be used in competition. B. The number of available compounds, configurations, and quantities available for use at each event will be announced coincident with the announcement of the Official Tire of the series and may be altered during the course of the 2009 season per safety, wear and related experience. 3. FUEL A. Official Fuel – The Official Fuel of AMA Pro Racing is XXXXXXXX and its exclusive use in unadulterated form shall be mandatory. B. Only air may be mixed with the fuel as an oxidant, and no other substances, chemicals and/or liquids whatsoever shall be added, combined, mixed and/or introduced to said Official Fuel whether intentionally or unintentionally unless approved in advance in writing by the AMA for use by all competitors. C. All competitors must use the official fuel, as supplied by the manufacturer at the track, during all on-track sessions. D. All motorcycles must prominently display the appropriate unmodified official fuel company decal on the motorcycle at all times. E. AMA Pro Racing has the right to sample a competitor’s fuel at any time. F. Competitors are responsible for the safe and proper handling and security of their fuel from when it is dispensed to them until it is used. G. Competitors are responsible for properly disposing of all unused fuel. 4. WHEELS/BRAKES A. Original equipment wheels must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. (1) Front wheels = 17″ x 3.5″ all machines (2) Rear wheels = 17″ x 5.5″ or 17″ x 6″ (See TIF for each machine) B. Original equipment brake calipers must be used, except where a TIF provides for substitutes. Substitutes must appear on the Eligible Equipment List. C. Aftermarket brake pads and lines may be substituted by homologated units appearing on the Eligible Equipment List.. D. The brake master cylinders may be substituted by homologated units appearing on the Eligible Equipment List. E. With approval of the Technical Inspector, front wheel spacers may be made “captive”. F. With approval of the Technical Inspector, rear wheel spacers may be made “captive”, and a caliper retaining device may be used. Chain adjuster must be OEM. 5. FRONT SUSPENSION A. Original front forks must be retained, including inner and outer tubes, fork bottoms, caliper mounts, axles and spacers. B. Aftermarket Cartridge kits appearing on the Eligible Equipment List are permitted and aftermarket fork caps may be substituted. C. A steering damper may be installed with a homologated unit appearing on the Eligible Equipment List. D. A fork brace may be installed with a homologated unit appearing on the Eligible Equipment List. E. Triple Clamps may be substituted with a homologated unit appearing on the Eligible Equipment List. F. Front suspension modifications are limited to: (1) Internal parts may be modified consistent and within the foregoing restrictions, including substitution of springs, change of shims and/or spacers, and addition of kit/aftermarket valving units appearing on the Eligible Equipment List. (2) External Compression Adjusters may be modified/changed. (3) Steering Head inserts to adjust rake may be used as long as no part of the frame is modified. 6. REAR SUSPENSION A. The original model, stock swingarm must be retained, unchanged, except that the axle adjustment opening/slot may be lengthened, with the permission of the Technical Inspector. B. The rear shock linkage may be substituted with a homologated unit appearing on the Eligible Equipment List. C. The rear shock may be modified or replaced by units appearing on the Eligible Equipment List. 7. FRAME/ADJUSTABLE PIVOT A. Unless otherwise provided for on the TIF, the original frame must be used. Unnecessary brackets may be removed. B. Adjustable swingarm pivots are permitted, but no modifications to the frame or swingarm can be made to allow this adjustability. 8. BODYWORK/CONTROLS/APPEARANCE A. Aftermarket, OEM-style bodywork and custom fairing mounts may be used. B. The fairing must match the shape of the OEM machine in silhouette and profile and the AMA shall have the right to use templates and go-no-go devices therefor. 1) An oil retaining, “sealed” lower fairing is mandatory. C. The stock gas tank must be used, but aftermarket gas caps are allowed. D. A front fender must be mounted. E. Aftermarket footpegs, clip-on bars, shift/brake mechanisms and fasteners may be used. F. Non-standard “Kill Switches” must not be spring loaded and must be well marked. G. Titanium Fasteners are not permitted. H. Tail sections may be increased in size to allow for required number display. Final approval rests with the Chief Technical Inspector. (1) AMA Pro retains the right to require number plates on machines with small or unusually sized or shaped tail sections. I. Numbers must be a minimum of 8 inches high and in a clear contrasting color to the background area on which they are displayed. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) No modifications are allowed except as follows: a. Cylinder head, cylinder and crankcase gasket surfaces only may be machined for increased compression. All other surfaces of the cylinder head, cylinder and crankcases must remain absolutely as homologated with no metal removal. b. Light cleaning of gasket surfaces with steel wool, Scotch- Brite®, etc. is permitted. Deburring radius of machined area must not be greater than 0.020 inches or 0.5mm. c. The cylinder head gasket may be changed. d. The valves, valve seats, guides, springs, tappets, oil seals, shims, cotter valve, spring base and spring retainers must be as originally produced by the manufacturer for the homologated machine. Valve spring shims are allowed. B. Camshaft (1) No modifications are allowed. (2) At the technical checks: for direct cam drive systems, the cam lobe lift is measured; for non direct cam drive systems (i.e. with rocker arms), the valve lift is measured. (3) The timing of the camshaft is free. C. Cam Sprockets (1) No dimensional modifications are allowed. (2) Cam sprockets may be slotted solely for the purpose of altering cam timing. (3) Press-on cam sprockets may be replaced with aftermarket steel bolt-on cam sprockets and adapters. (4) Aftermarket cam chain tensioners are permitted. D. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. E. Oil Pumps and Oil Lines (1) No pump modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. F. Connecting Rods (1) No modifications are allowed (including polishing and lightening). G. Pistons (1) No modifications are allowed (including polishing and lightening). H. Piston Rings (1) No modifications are allowed. I. Piston Pins and Clips (1) No modifications are allowed. J. Cylinders (1) No modifications are allowed except as provided for above. K. Crankcase and all other Engine Cases (i.e. ignition case, clutch case, etc.) (1) No modifications to the crankcases are allowed except as provided for above. (2) Lateral (side) covers may be altered, modified or replaced. If replaced, the cover must be made in material of same or higher specific weight and the total weight of the cover must not be less than the original one. (3) On motorcycles where lateral covers or engine cases contain oil, strengthened engine side covers or case guards must be installed. All such protection devices must weigh no less than the original homologated parts and must be approved by the AMA Pro Tech Inspector. L. Transmission/Gearbox (1) Kit-type Electronic “quick shifters” are allowed. (2) Manual “secondary” hand operated kill switch/quick shifters are not allowed. (3) Final drive system, if not by chain, may be modified to chain type, utilizing kits specified on the Eligible Equipment List. (4) Original equipment shift drum detent stars may be modified or replaced with approved, homologated aftermarket parts. (5) Other modifications to gearbox or selector mechanism are not allowed. M. Countershaft sprocket, rear wheel sprocket, chain pitch and size can be changed. (1) The sprocket cover can be modified. N. Stock carb bodies or stock fuel injection systems must be used, but carb internals, velocity stacks and injection management systems may be altered or replaced. O. Injectors must be stock and unaltered from the original specification and manufacture. P. Aftermarket exhaust systems appearing on the Eligible Equipment List may be installed. Q. “Dry Clutches” are only permitted when used on the equivalent OE production model. R. Aftermarket “Slipper” clutches appearing on the Eligible Equipment List are permitted. S. Homologated engine control unit (ECU), must be either: (1) As homologated and inner software can be changed; (2) Or the ECU kit model (produced and/or approved by the machine Manufacturer) can be used. (3) A special connector can be used to connect the kit ECU and the original wire loom. 10. AIR BOX/INTAKE/SCOOPS A. Original equipment air box is required, without modification. B. An air filter is required. Original equipment air filter and air filters appearing on the Eligible Equipment List are permitted. C. Ram air systems are permitted if specified and used on the homologated motorcycle. Ducts and scoops, must be identical in specification to the original equipment system. 11. POST QUALIFYING/POST RACE TECH A. Immediately following each qualifying session or race, the top three finishers plus other motorcycles chosen at random at the discretion of AMA Pro will be secured for inspection by AMA Pro staff members. B. Motorcycle weights will be checked immediately following qualifying or races, in the same condition in which they finish the activity, including all fluids such as oil, water and fuel. C. No fluid and/or any other item(s) may be added to the motorcycle prior to the determination of weight.

2009 AMA Pro Racing Factory Superbike Rules

2009 BASIC EQUIPMENT REGULATIONS FOR ROAD RACING COMPETITION Factory Superbike Equipment Regulations All machines eligible for participation in Factory Superbike must be approved by AMA Pro Racing and homologated by the manufacturer. All items not mentioned in the following articles must remain as originally produced by the manufacturer for the homologated machine. EVERYTHING THAT IS NOT AUTHORIZED AND PRESCRIBED IN THESE REGULATIONS IS STRICTLY FORBIDDEN. In addition, every motorcycle entered must meet the requirements listed in General Equipment Standards. 1. DISPLACEMENT CAPACITIES AND WEIGHT LIMITS A. Minimum weight in the exact condition the machine finishes any competition activity (qualifying or race final) without the addition of fluids or other items of any kind. (1) 4 cylinder 375 pounds (2) 2 cylinder 390 pounds B. Displacement capacities (1) 4 cylinders 749cc up to 1000 cc 4-stroke. (2) 2 cylinders 901cc up to 1200 cc 4-stroke (3) Engine type, configuration, stroke and any modifications of engine components to alter the stock OEM firing order of the cylinders are not permitted. (4) The displacement capacities must remain at the homologated size. Modifying the bore and stroke to reach class limits is not allowed. 2. TIRES A. Any tire approved by the tire manufacturer for racing is allowed. 3. FUEL A. To be determined. 4. WHEELS/BRAKES A. Wheels (1) Wheels and associated parts may be modified or replaced from those fitted to the homologated motorcycle. (2) Carbon fiber or carbon composite wheels are not allowed. (3) Bearings, seals and axles may be altered or replaced from those fitted to the homologated motorcycle. (4) Rear wheel sprocket and brake rotor must remain with the wheel unless part of the original homologated design. (5) Maximum rear wheel rim width: 6.25 in. B. Brakes (1) Front and rear master cylinder including lever/pedal may be modified or replaced from those fitted to the homologated motorcycle. (2) Front and rear calipers may be modified or replaced from those fitted to the homologated motorcycle. (3) Brake pads or shoes may be modified or replaced from those fitted to the homologated motorcycle. (4) Brake hoses and brake fittings may be modified or replaced from those fitted to the homologated motorcycle. (5) Brake discs may be modified or replaced from those fitted to the homologated motorcycle. (6) The use of carbon fiber, carbon composite or titanium materials for brake discs is not allowed. 5. FRONT SUSPENSION A. Front forks in whole or part may be modified or replaced from those fitted to the homologated motorcycle. B. Front Forks must be the same type on the homologated motorcycle (leading link, telescopic, upside down, etc.). C. The upper and lower fork clamps (triple clamp, fork bridges) including steering stem, can be changed or modified. D. Steering damper may be added, relocated or replaced with an aftermarket damper. E. The steering damper cannot act as a steering lock limiting device. F. Active, semi-active or computer-controlled suspension units are not permitted. 6. REAR SUSPENSION A. Rear suspension unit can be changed but a similar unit must be used (i.e. dual or single shock). B. The rear suspension linkage may be modified or replaced. 7. FRAME A. Frame and Sub Frame (1) The main Frame must remain as originally produced by the manufacturer for use on the homologated motorcycle with the following modifications allowed: (2) Strengthening gussets and tubes may be added, but none may be removed. (3) Accessory brackets (radiator, shock reservoir, stands, etc.) may be changed, relocated, added or removed. Holes may be drilled only for the purpose of attaching brackets or other components. (4) The homologated dimensions and the position of the steering head, engine, swing arm pivot point, rear shock, and suspension linkage mounting points must remain as homologated on the original machine. (5) The use of offset bearing races for the purpose of altering the steering angle is allowed. (6) The swing arm pivot location may only be adjusted if the design was part of the homologated frame. (7) Rear sub frame may be modified or replaced, but the material must remain as homologated. (8) Polishing of frame materials is not allowed. (9) Frame must display vehicle identification number. B. Swingarm (1) Swingarm may be modified or replaced. (2) The use of carbon fiber or Kevlar® materials are not allowed if not homologated on the original machine. (3) Rear wheel stand mounts may be added to the swingarm by welding or by bolts. Brackets must have rounded edges (with a large radius). Mounting bolts must be recessed. 8. BODYWORK/CONTROLS/APPEARANCE A. Fairing and Bodywork (1) Fairing and bodywork, including the front fender and windscreen may be modified or replaced with aftermarket parts which resemble the originally approved parts in design and which maintain similar dimensions. (2) Construction must be of plastic or fiberglass (no carbon or carbon composite fiber) (3) See Fairing and Bodywork under General Equipment Standards for other restrictions and fluid containment. (4) With permission from the Race Manager or the Chief Technical Inspector, fairing or bodywork may be removed only if damaged at that particular meet. This does not include the oil retention portion of the lower fairing. B. Seat (1) Seat may be altered or replaced from those fitted to the homologated motorcycle. (2) The top portion of the rear bodywork around the seat may be modified to a solo seat. (3) The solo seat then must incorporate the rear number plate. (4) The appearance from both front rear and profile must conform in principle to the homologated shape. (5) The seat/rear cowl must allow for proper number display. (6) All exposed edges must be rounded. (7) Construction must be of plastic or fiberglass (no carbon or carbon composite fiber). C. Instrument Panel (1) Aftermarket instrument panels are allowed. (2) A shift/indicator light may be added even if one did not exist from the factory. D. Foot Rest/Foot Controls (1) Foot rest/foot controls may be may be modified, relocated or replaced from those fitted to the homologated motorcycle. (2) Foot rests may be rigidly mounted or a folding type which must incorporate a device to return to the normal position. (3) The end of the footrest must have an 8mm solid spherical radius. E. Handle Bars and Hand Controls (1) Handle bars, hand controls and cables may be altered or replaced from those fitted to the homologated motorcycle. (2) Engine stop switch must be located on the handlebars. 9. ENGINE MODIFICATIONS A. Cylinder Head (1) Cylinder heads must remain as homologated with the following modifications allowed. (2) Porting and polishing of the cylinder head and INTAKE MANIFOLD normally associated with individual tuning such as gas flowing of the cylinder head, including the combustion chamber is allowed. (3) Welding or the addition of material is allowed. (4) The compression ratio is unrestricted. (5) Combustion chamber may be modified. (6) Replacement valve seats and guides are permitted. B. Cylinders (1) Only the following modifications to the cylinders are allowed. Cylinder head gasket surface may be machined to allow the adjustment of compression ratio or resurfacing to repair a warped cylinder surface deck. (2) Homologated materials and castings for cylinders must be used. (3) Cylinder liners or coatings may be replaced or added. C. Crankcase and all other Engine Cases (i.e. ignition case, clutch case). (1) Crankcases must remain as homologated. No modifications are allowed. (2) Engine case guards in the form of strengthened engine side covers or approved guards must be installed on certain models. Replacement covers must be no lighter in weight than the stock covers. See Engine under General Equipment Standards. (3) The countershaft cover may be removed. (4) The addition of a crankcase protector at the countershaft is allowed. D. Valves, Springs, and Retainers (1) Aftermarket or modified valves, springs, retainers and other valve-train components are permitted. The original number of valves must be maintained. (2) Valve diameter and minimum weight, including stem, must remain as homologated. (3) Valves must remain in the same location and at the same angle as the homologated model. (4) The material and dimensions of the rocker arms (if any) must remain as homologated. (5) The material of the tappets/buckets must remain as homologated. E. Camshafts and Sprockets (1) The original camshaft may be modified or replaced from those fitted to the homologated motorcycle. (2) The method of drive must remain as homologated. (3) The duration is unrestricted but the lift must remain as homologated. (4) The tensioning devise(s) for the cam chain or cam belt is unrestricted. (5) Cam sprockets can be modified or replaced to allow the degreeing of camshafts. F. Crankshaft (1) Crankshaft must remain as homologated with the following modifications allowed. (2) Balancing. This may only be achieved by the same method used by the OEM. For example, heavy metal (i.e. Mallory metal) inserts are not permitted unless they were originally specified by the OEM. (3) Bearing surfaces may be polished or surface treated. (4) Polishing and lightening of the crankshaft is not allowed. (5) Primary gears can not be changed or modified. (6) Oil galley plugs may be modified, removed or replaced. G. Connecting Rods (1) Connecting rods must remain as homologated. No modifications are allowed. (2) Polishing and lightening is not allowed. H. Pistons (1) Pistons must remain as homologated. No modifications are allowed. (2) Polishing and lightening is not allowed. I. Piston Rings (1) Piston rings must remain as homologated and installed. No modifications are allowed. J. Piston Pins and Clips (1) Piston pins and clips must remain as homologated. No modifications are allowed. K. Oil Pumps and Oil Lines and Water Pumps (1) Oil pump must remain as homologated. Modifications are allowed. (2) Oil lines may be modified or replaced. Oil lines containing positive pressure, if replaced, must be of metal reinforced construction with swaged or threaded connectors. (3) The internal parts of the water pump may be changed or modified. The drive ratio may be changed. The external appearance must remain as homologated. (4) Water lines may be modified or replaced. L. Clutch (1) Clutch type (wet or dry) must remain as homologated. (2) Aftermarket, modified or stock-type clutches with back-torque limiting capabilities are permitted. M. Transmission Shafts and Gear Sets (1) Two options are available for these components: a. Stock transmission shafts and gear sets. a) Undercutting and surface treatments are the only modifications allowed. b. Approved transmission shafts and gear sets. a) Each manufacturer will be permitted one alternative set of gear ratios per approved model. b) Approved shafts and gears may be interchanged with stock components. c) Undercutting and surface treatments are the only modifications allowed. (2) Only shafts and gears sold through the OEM distributor or its dealers are permitted. (3) Approved transmission components must be available individually or as a set to AMA Superbike-licensed riders for the entire current season (or the remaining part of the season). (4) Orders determined to be legitimate by AMA Pro Racing and accompanied by a 50% deposit must be filled within 15 business days of receipt by the OEM distributor or dealer. (5) Retail price of individual approved transmission components may not exceed twice the manufacturer’s suggested retail price of the components they replace. (6) If a manufacturer does not offer optional AMA Pro Racing approved transmission components, then the stock components must be retained. N. Fuel injection system and throttle-body assemblies (1) Fuel injection throttle body assemblies must remain as homologated. (2) Assemblies include all attached parts with the exception of fasteners, cables, cable actuating pulleys, flexible fuel lines, vacuum lines, air box connection tubes and velocity stacks. (3) Variable-length fuel injection intake tract devices that function while the engine is operating are prohibited unless it is standard equipment on the homologated OEM production model. (4) Fuel injectors may be replaced with aftermarket units provided the original mounting locations are maintained and no modifications are made to the throttle body assemblies for injector fitment. The total number of installed injectors must be the same as originally produced. (5) Secondary butterfly valves may be fixed in the open position. (6) Fuel pump and fuel pressure regulator must remain as homologated with no modifications. O. Engine Control System (1) Engine control system may be modified or replaced with aftermarket products. (2) Wiring harness may be modified or replaced. (3) Spark plugs and plug wires may be replaced. (4) Data acquisition is allowed. (5) Aftermarket sensors re permitted. P. Generator (1) The generator may be modified or replaced. (2) The starting system, electrical or manual may be modified or replaced but must work. 10. AIR BOX/INTAKES/FUEL SUPPLY A. Intake Air Boxes (1) Air box must remain as originally produced by the manufacturer on the homologated motorcycle. (2) Air filters, internal flap type valve, sensors and vacuum fittings may be removed, modified, or replaced with aftermarket parts. Any holes in the air box to the outside atmosphere resulting from the removal of components must be completely sealed from incoming air. (3) All incoming air must pass through the original, unmodified air box inlets. (4) Ram air tubes or ducts may be modified, replaced with aftermarket parts or removed. If tubes/ducts are utilized, they must be attached to the original, unmodified air box inlets. (5) Velocity stacks may be modified, replaced with aftermarket parts or removed. The only modification permitted to the air box to allow use of alternate velocity stacks is the removal of internal debris deflectors/plates. B. Fuel Tanks (1) Fuel tank may be modified or replaced provided that it maintains the stock appearance. (2) Non metallic fuel tanks are not allowed. (3) Fuel tanks may be modified to achieve a maximum capacity of 24 liters (6.341 gallons). (4) The fuel cap may be replaced with a quick-fill coupler and additional vent coupling. Both couplers must be installed in the top of the tank. (5) Maximum inner diameter of quick-fill or vent coupler is 63.5mm (2.5″). C. Fuel Supply (1) Fuel petcocks may be modified or replaced. (2) Fuel lines may be replaced. (3) Quick connectors or dry break quick connectors may be used. (4) Fuel vent lines may be replaced. (5) Fuel filters may be added. 11. MISCELLANEOUS A. Exhaust System (1) The exhaust pipes and silencers may be modified or replaced from those fitted to the homologated motorcycle. (2) Catalytic converters must be removed. (3) For safety reasons, the exposed edge(s) of the exhaust pipes(s) outlet(s) must be rounded to avoid sharp edges. B. Radiators and oil coolers (1) The original radiator or oil cooler may be modified or replaced from those fitted to the homologated motorcycle. (2) Additional radiators and oil coolers are allowed. (3) Oil coolers must not be mounted on or above the rear mudguard. (4) The appearance from the front, rear and profile of the machine must in principle conform to the homologated shape after the addition of additional radiators or oil coolers. C. The following items may be modified or replaced from those fitted to the homologated motorcycle. (1) Any type of lubrication, brake or suspension fluid may be used. (2) Any type of spark plug and plug cap may be used. (3) Gasket and gasket material (4) Bearings (ball, roller, taper, plain, etc.) of any type or brand may be used. (5) Fasteners (nuts, bolts, screws etc.) (6) Main wiring harness and connectors. (7) Battery and switches. (8) Countershaft sprocket, rear wheel sprocket and chain. (9) Oil and fuel filters D. The Following Items May Be Removed (1) Instrument and instrument bracket and associated cables. (2) Radiator fan and wiring (3) Cooling system thermostat (4) Chain guard.

DMG Announces 2009 AMA Pro Racing Plans

AMA PRO RACING OFFERS THREE SUPERBIKE CLASSES FOR 2009 DAYTONA BEACH, FLORIDA (JULY 19, 2008) – Today DMG released their plan for the 2009 AMA Superbike Series. Last week the contract with AMA and DMG was unanimously approved by the AMA Board of Trustees. In the future, DMG will do business as AMA Pro Racing and further releases will be under that trade name. After four months of meetings and discussions, listening to suggestions, comments, and ideas from the broad spectrum of interested parties, AMA Pro Racing is presenting a program designed to provide exciting competition that will appeal to fans and participants alike. “The program we are releasing today represents the best combination of our vision and the vision shared with us by the manufacturers, promoters, fans, and independent teams” said Roger Edmondson of AMA Pro Racing. The primary classes are Factory Superbike, American Superbike, and Daytona Superbike. Each of the classes has their own regulations and character. Secondary programs include the Red Bull AMA US Rookies Cup and Sun Trust Moto-ST, which will be added at select events. Time will be built into each race weekend format to allow for local special activities, fan-walks on pit road, extended pre-race rider introductions, and post-race podium celebrations, complete with public rider interviews for fans and private briefings for the press. Factory Superbike is a new program, free from the constraints of attempts to balance the resources of the factory teams to those of private entries. Featured are liter class sport bikes, operating at the highest level of technology and performance. Plans call for full implementation of FIM World Superbike rules by 2011, but to ease the transition from current equipment, in 2009 Factory Superbikes will be prepared to the specifications agreed to in 2007 by the AMA Rules Committee and manufacturers. Honda, Suzuki, Kawasaki and Yamaha, have all requested use of those rules for 2009. The required Factory Pro license will only be issued to riders with a proven record of experience and performance at the top level of the sport. Other features of this new competition include single-bike qualifying, open tire selection, and unlimited testing. Factory Superbike will be the final race on most event weekends. “Works bikes, salaried star riders, rules written by and requested by the manufacturers, special tires, no-holds barred superbike racing by the strongest teams in America…..what more could a racing fan ask for?” said Edmondson. “It will be a shooting war among the big guns and the meek need not apply.” American Superbike is for the same big-bore machines as Factory Superbike, but at a lower level of modification and performance. As in FIM World Superbike, there will be a single tire supplier. All approved machines and after-market parts will be homologated, and must be available to all competitors. Testing will be limited to reduce costs to the teams and sponsors. “SuperPole” qualifying for the ten fastest riders in timed practice will set the front of the grid. Riders in American Superbike must have a Factory Pro or Superbike Pro license. Motorcycles entered in American Superbike may not be entered in Factory Superbike. Daytona Superbike departs from the traditional displacement and weight regulations and introduces power-to-weight and dynamometer controls to limit horsepower. This class is expected to be contested mostly by 600cc four-cylinder motorcycles, however the rules will provide for close competition with 675cc triples and up to 1200cc twins. All approved machines and after-market parts will be homologated, and must be available to all competitors. Daytona Superbike will feature Superpole qualifying, limited testing, single tire and fuel suppliers, and may be contested by all Superbike licensed riders (Factory Pro, Superbike Pro, and Limited Pro). Homologation of motorcycles and approved after-market accessories and parts will begin August 1st. Provisional rules are attached to this release. The Official Rule Book will be published in September.

Updated: Bayliss Wins World Superbike Superpole At Brno

FIM Superbike World Championship Brno, Czech Republic July 19, 2008 Superpole Results (all on Pirelli tires): 1. Troy BAYLISS (Ducati 1098 F08), 1:58.345 2. Troy CORSER (Yamaha YZF-R1), 1:58.451 3. Michel FABRIZIO (Ducati 1098 F08), 1:58.853 4. Max BIAGGI (Ducati 1098 RS08), 1:59.069 5. Ryuichi KIYONARI (Honda CBR1000RR), 1:59.318 6. Niccolo CANEPA (Ducati 1098 F08), 1:59.324 7. Fonsi NIETO (Suzuki GSX-R1000), 1:59.360 8. Jakub SMRZ (Ducati 1098 RS08), 1:59.451 9. Max NEUKIRCHNER (Suzuki GSX-R1000), 1:59.497 10. Yukio KAGAYAMA (Suzuki GSX-R1000), 1:59.537 11. Ruben XAUS (Ducati 1098 RS08), 1:59.545 12. Noriyuki HAGA (Yamaha YZF-R1), 1:59.571 13. Carlos CHECA (Honda CBR1000RR), 1:59.587 14. Lorenzo LANZI (Ducati 1098 RS08), 1:59.639 15. Karl MUGGERIDGE (Honda CBR1000RR), 2:00.306 16. Ayrton BADOVINI (Kawasaki ZX-10R), 2:01.161 The Rest of the Grid: 17. David CHECA (Yamaha YZF-R1), 2:00.228 18. Shinichi NAKATOMI (Yamaha YZF-R1), 2:00.232 19. Gregorio LAVILLA (Honda CBR1000RR), 2:00.304 20. Roberto ROLFO (Honda CBR1000RR), 2:00.374 21. Regis LACONI (Kawasaki ZX-10R), 2:00.482 22. Makoto TAMADA (Kawasaki ZX-10R), 2:00.641 23. Shuhei AOYAMA (Honda CBR1000RR), 2:00.905 24. Sebastien GIMBERT (Yamaha YZF-R1), 2:01.059 25. Vittorio IANNUZZO (Kawasaki ZX-10R), 2:01.214 26. Kenan SOFUOGLU (Honda CBR1000RR), 2:01.302 27. Jiri DRASDAK (Honda CBR1000RR), 2:02.373 28. Christian ZAISER (Yamaha YZF-R1), 2:03.118 29. Jason PRIDMORE (Honda CBR1000RR), 2:03.397 30. Milos CIHAK (Suzuki GSX-R1000), 2:03.758 More, from a press release issued by Team YZF Yamaha Nakatomi only 0.007 from the Superpole For less than one hundredth of a second, Shinichi Nakatomi could not qualify for the Superpole. He was in 18th position and he is looking for a good race. He finished 8th in Brno in 2006 and 9th in 2007. On Friday, the Japanese rider was 17th, 1.4 seconds behind the provisional pole position. On Saturday, he barely missed the qualification for the top 16 who go to Superpole even if his lap time was faster than the day before. The team could be proud of the best top speed, the Yamaha R1 being the fastest motorcycle of the whole field. Shinichi Nakatomi: “We worked a lot on the set up and we made some progress, but the other teams too. My times have been faster and faster, but it was the same for the other riders. My feeling is not so bad, even if the grid position is not so good. The times are very close. We worked well on the set up for the race.” Martial Garcia (team-manager): “The practices have been positive, even if the final result is that we are not in Superpole for 0.007, only 1.2 seconds from the best time. We made a good choice of tyres, despite the aggression of the new track surface. We tested on the race distance with lap times between 2.01 and 2.02, which is one second faster than last year. We are confident for the races because the potential is very good.” Qualifying results: 1-Bayliss (Ducati), 2-Corser (Yamaha), 3-Fabrizio (Ducati), 4-Biaggi (Ducati), 5- Kiyonari (Honda)”¦18- Nakatomi (Yamaha) World Championship standings: 1- Bayliss (Ducati) 259, 2- Neukirchner (Suzuki) 210, 3- Checa (Honda) 207, 4- Haga (Yamaha) 191, 5- Corser (Yamaha) 185″¦19- Nakatomi (Yamaha) 24 Round 10 of the Superbike World Championship: August 3 / Brands Hatch (United Kingdom) Team YMF Yamaha Superstock YZF Yamaha Junior Team FIM Cup Superstock 1000 Superstock 600 European Championship Baz 2nd behind Vostarek Brilliant race for Loris Baz who finished second behind the local rider Patrick Vostarek, who is racing here for the 9th time today on this track. Thanks to this great performance, Baz is still leading the championship. Sylvain Barrier qualified in 14th position for the 1000 cc race that will be held tomorrow. Vostarek had the best start and Baz, in third position, was slowed down by the second Rea. Then Baz overtook Rea and was second at the end of the first lap, 1.2 behind Vostarek. He got closer and closer and he was right behind the Czech at half distance after 5 laps. Rea was in third, quite far 10 seconds behind the leaders. After that, Vostarek and Baz had an incredible fight, with the Frenchman taking the lead on lap 8 before Vostarek took the lead back. Both riders arrived together at the finish line, with a little advantage for Vostarek. With this great performance, Loris Baz keeps the championship lead, with now a 7 points advantage over Vostarek. Loris Baz: « A good start was a must not to let Vostarek take too much of a lead. I knew that after 4 laps with the race tyres I was 0.5 to 1 second faster than him. But Gino Rea had a terrific start and he was hard to overtake. I passed him but he passed me back, had a big slide that slowed me down. I finally passed him and had to catch the leader. I was then 0.7 second faster than him on one lap, and he missed the inside of a curve so I caught him. While I was behind him, I tried to see where I could pass him, but it was very difficult because he knows the track very well. I passed him two laps before the end, but after that I could do nothing because my front tyre was no more performing well. I was crossing the front wheel all the time. I had to use my knee to keep my balance. This is a good weekend. My motorcycle was perfect. Thank you very much to the team. » Difficult practices for Sylvain Barrier in the 1000 cc class, because of a small technical problem on Saturday morning during the free session. Then he was fast in the afternoon for the timed session and he was 14th despite a little crash. Martial Garcia (team-manager): “Loris Baz did a very beautiful race. A slower rider was hard to pass in the first lap but Loris passed him and came back right behind the leader. He tried very hard to win this race and his second position makes him stay the leader of the championship. I a very satisfied. Sylvain Barrier had a small technical problem in the morning and he was much faster in the afternoon despite a small crash with no consequence. He is 14th and we are very confident.” FIM Cup Superstock 1000 qualifying results: 1-Roberts (Ducati), 2-Pirro (Yamaha), 3-Berger (Honda), 4-Siméon (Suzuki), 5-Corti (Yamaha)”¦14- Barrier (Yamaha) FIM Cup Superstock 1000 standings: 1- Simeon (Suzuki) 84 points, 2- Roberts (Ducati) 76, 3- Polita (Ducati) 67, 4- Pirro (Yamaha) 63, 5- Berger (Honda) 59″¦25- Barrier (Yamaha) 4 Superstock 600 European Championship race results: 1-Vostarek (Honda), 2- Baz (Yamaha), 3- Rea (Yamaha), 4- Linfoot (Yamaha), 5- Bussolotti (Yamaha), Superstock 600 European Championship standings: 1- Baz (Yamaha) 117 points, 2-Vostarek (Honda) 110, 3- Linfoot (Yamaha) 74, 4- Bussolotti (Yamaha) 71, 5- Rea (Yamaha) 61 More, from a press release issued by Sterilgarda Go Eleven: There are all the makings of a great day for Sterilgarda Go Eleven tomorrow on the occasion of the race of the 9th WSBK round at Brno: Max Biaggi and Ruben Xaus are going to start from the first and the third line respectively, after having shown during all the four practice sessions to have what it takes to confirm to finish in the top positions of both the race. Max Biaggi likes this track, he recorded the pole after the second timed session and he took the first row after the Superpole. Ruben Xaus worked with the bike in race-trim for the whole two days of qualifying before an hitch at the rear damper of his bike prevented him from getting a better result from his Superpole. In Superstock1000 Alex Polita is going to start from the second line. Like his SBK team-mates, the “Pirate” is going to face the race with the goal to take a final place in the first positions. Weather is unpredictable for tomorrow, every kind of situation is expected and all the team are in a state of uncertainty. RUBEN XAUS | Ducati 1098 RS | 11th classified in 1’59.545: “I wished to get more from my Superpole but the rear damper didn’t work as we expected after having analysed the data of the free practices. I will start from the third line after having done a good work and make meaningful improvements on a track on which I have never felt comfortable. I think I can aim to run two good race and I would like to thank the team for the excellent job done”. MAX BIAGGI | Ducati 1098 RS | 4th classified in 1’59.069: “We have done a good job for the two race. In Superpole I would have liked to confirm the pole-position recorded in the second timed session, anyhow the first line is an excellent starting position”. ALEX POLITA | Ducati 1098R | 7th best time in 2’04.734: “I feel confident with the race which I’m going to face with the goal to fight for a final place in the top positions. During the second timed session I improved my time markedly so we needed to make a little setting change in order to increase the traction. Anyhow we are partway through this solution which is going to be test tomorrow during the warm-up”. More, from a press release issued by FGSport Group: Bayliss grabs Superpole with record lap at Brno Troy Bayliss (Ducati Xerox) grabbed Superpole for round 9 of the WSBK championship with a blistering record lap of 1 minute 58.345 seconds at the newly-resurfaced Automotodrom Brno circuit. Today’s pole was the 22nd of the points leader’s career, and his fourth this season, a result that takes him past Carl Fogarty in the all-time pole classification into second behind Troy Corser on 42. Bayliss’s chief rival today in Superpole was in fact Corser (Yamaha Motor Italia WSB), who was just one tenth of a second down. Third quickest was Bayliss’s Ducati Xerox team-mate Michel Fabrizio, while fourth went to another Italian Max Biaggi (Sterilgarda Go Eleven Ducati), quickest overall in qualifying. Troy Bayliss: “It hasn’t always looked good on this track for us, especially last year, and it’s been a bit of a bogey track for me as well. I’ve never really had great results here in the past and I’d love to turn that around. When I saw Corser’s lap I knew I had to do a good one to beat that and when Max was out, I would have given him a real pat on the back if he had gone faster than that.” Troy Corser: “There’s always a risk when you go out before the end of the Superpole and set the quickest time, especially when Bayliss is around because I know he’s going to grit his teeth and try and get there. But we’ve got a really good set-up for race tyres tomorrow, we’ve done a pretty good race distance and it’s all looking really good.” Michel Fabrizio: “I really like this circuit and I’ve always gone well here. We’ve done a great job during the weekend and my race pace is pretty good. I wanted to go even better in Superpole but unfortunately there’s a ‘granddad’ alongside me who always pulls out something special. But third is a good result and I’m really satisfied.” Max Biaggi: “I really like the Brno track and love racing here. I think we’ve learnt a lot this weekend and for today fourth place is OK. I wanted to go faster a little bit but it didn’t happen. My team and I have done a good job to get on the front row of the grid, which is good because we’re going to have to start well and be up at the front tomorrow.” The biggest mover today was Ryuichi Kiyonari (Hannspree Ten Kate Honda), who powered to fifth place and a row 2 start in Superpole after qualifying for the one-lap dash in sixteenth. The Japanese rider will be accompanied by WSBK rookie Niccolò Canepa (Ducati Xerox), Spain’s Fonsi Nieto (Suzuki Alstare) and Czech star Jakub Smrz (Guandalini Ducati). Bayliss’s chief rivals in the championship failed to emerge, Max Neukirchner (Alstare Suzuki) and Noriyuki Haga (Yamaha Motor Italia WSB) both qualifying on the third row, while Carlos Checa (Hannspree Ten Kate Honda) is even further behind on row 4. Times: 1. Bayliss T. (AUS) Ducati 1098 F08 1’58.345; 2. Corser T. (AUS) Yamaha YZF-R1 1’58.451; 3. Fabrizio M. (ITA) Ducati 1098 F08 1’58.853; 4. Biaggi M. (ITA) Ducati 1098 RS 08 1’59.069; 5. Kiyonari R. (JPN) Honda CBR1000RR 1’59.318; 6. Canepa N. (ITA) Ducati 1098 F08 1’59.324; 7. Nieto F. (ESP) Suzuki GSX-R1000 1’59.360; 8. Smrz J. (CZE) Ducati 1098 RS 08 1’59.451; 9. Neukirchner M. (GER) Suzuki GSX-R1000 1’59.497; 10. Kagayama Y. (JPN) Suzuki GSX-R1000 1’59.537; 11. Xaus R. (ESP) Ducati 1098 RS 08 1’59.545; 12. Haga N. (JPN) Yamaha YZF-R1 1’59.571; 13. Checa C. (ESP) Honda CBR1000RR 1’59.587; 14. Lanzi L. (ITA) Ducati 1098 RS 08 1’59.639; 15. Muggeridge K. (AUS) Honda CBR1000RR 2’00.306; 16. Badovini A. (ITA) Kawasaki ZX-10R 2’01.161. FIM Supersport World Championship Broc Parkes (Yamaha World Supersport) was again quickest in the second and final WSS qualifying session. The 26 year-old Australian set a record lap of 2 minutes 3.204 seconds ten minutes from the end to grab his fifth successive Supersport pole. Parkes will be joined on the front row by the surprising Dutch rider Barry Veneman (RES Software Suzuki), who qualified ahead of Australians Joshua Brookes (Hannspree Stiggy Motorsport Honda) and points leader Andrew Pitt (Hannspree Ten Kate Honda). The second row is made up of Britain’s Craig Jones (Parkalgar Racing Honda), ahead of Mark Aitchison (Triumph BE1 Racing) and Jonathan Rea (Hannspree Ten Kate Honda) while Finland’s Vesa Kallio (Benjan Racing Honda) scored his best result of the year in eighth. Australian Garry McCoy (Triumph SC) had a nasty crash, suffering a cracked vertebra and a bruised right lung in the process. Times: 1. Parkes B. (AUS) Yamaha YZF-R6 2’03.203; 2. Veneman B. (NED) Suzuki GSX-R600 2’03.452; 3. Brookes J. (AUS) Honda CBR600RR 2’03.562; 4. Pitt A. (AUS) Honda CBR600RR 2’03.590; 5. Jones C. (GBR) Honda CBR600RR 2’03.761; 6. Aitchison M. (AUS) Triumph 675 2’03.775; 7. Rea J. (GBR) Honda CBR600RR 2’03.934; 8. Kallio V. (FIN) Honda CBR600RR 2’04.135. Superstock 1000 FIM Cup A Ducati also took pole position in Superstock 1000 qualifying, the Xerox Junior Team 1098 version of Australian Brendan Roberts, who was pushed hard by Italian Michele Pirro (Yamaha Lorenzini by Leoni). The other two riders on the front row are Maxime Berger (Hannspree IDS Ten Kate Honda) of France and points leader Xavier Simeon (Alstare Suzuki) of Belgium. Four Italians make up row 2, one of the race favourites Claudio Corti (Yamaha Motor Italia Junior Team), Andrea Antonelli (Althea Racing Honda), Alex Polita (Sterilgarda Go Eleven Ducati) and Domenico Colucci (Ducati Xerox Junior Team). Times: 1. Roberts B. (AUS) Ducati 1098R 2’03.685; 2. Pirro M. (ITA) Yamaha YZF-R1 2’03.924; 3. Berger M. (FRA) Honda CBR1000RR 2’03.929; 4. Simeon X. (BEL) Suzuki GSX-R1000 2’04.150; 5. Corti C. (ITA) Yamaha YZF-R1 2’04.156; 6. Antonelli A. (ITA) Honda CBR1000RR 2’04.601; 7. Polita A. (ITA) Ducati 1098R 2’04.734; 8. Colucci D. (ITA) Ducati 1098R 2’04.789. European Superstock 600 Championship – Race Czech youngster Patrick Vostarek (Intermoto Czech Honda) scored his third win in a row at the Automotodrom Brno after a battle right down to the last corner with Loris Baz (YZF Yamaha Junior Team), who still holds on to his points lead in the table. Third place went to Britain’s Gino Rea (StoneBaker Yamaha) who just edged out team-mate Dan Linfoot and Italian Marco Bussolotti (Yamaha Motor Italia Junior Team) for the final podium slot. Results: 1. Vostárek P. (CZE) Honda CBR600RR 19’12.257 (151,926 kph); 2. Baz L. (FRA) Yamaha YZF-R6 0.349; 3. Rea G. (GBR) Yamaha YZF-R6 16.862; 4. Linfoot D. (GBR) Yamaha YZF-R6 17.037; 5. Bussolotti M. (ITA) Yamaha YZF-R6 17.072; 6. Black G. (GBR) Yamaha YZF-R6 17.226; 7. Jezek O. (CZE) Kawasaki ZX-6R 17.454; 8. Biliotti L. (ITA) Honda CBR600RR 22.382. Points (after 6 of 10 rounds): 1. Baz (Yamaha) 117; 2. Vostarek (Honda) 110; 3. Linfoot (Yamaha) 74; 4. Bussolati (Yamaha) 71; 5. Rea (Yamaha) 61; 6. Petrucci (Yamaha) 56; 7. Beretta (Suzuki) 53; 8. Black (Yamaha) 37. More, from a press release issued by Yamaha Racing: Corser just misses Superpole win Troy Corser (Yamaha Motor Italia WSB Team) missed out on his 43rd career Superpole win by a mere 0.106 seconds at the 5.403km Brno circuit today, with only his fellow Australian Troy Bayliss able to beat his time. The fight for the new absolute track record was played out in warm and dry conditions and on qualifying tyres. Corser set a 1’58.451 to take what looked like an unbeatable time, only for Bayliss to fight back. Noriyuki Haga (Yamaha Motor Italia WSB Team) worked hard in session with the team but could not find a set-up that allowed his proven talents at Brno to shine and he now starts the races on Sunday from the third row of the grid, 12th overall. David Checa (Yamaha GMT94) came agonisingly close to joining the top 16 qualifiers in Superpole, but now starts the race from the 17th grid slot. Shinichi Nakatomi (Team YZF Yamaha) was only 0.004 seconds from Checa, in a positive final qualifying session. Sebastien Gimbert (Yamaha GMT94) was 24th after losing some track time in practice today. Troy Corser (2nd – 1’58.451 – Yamaha Motor Italia WSB Team) “It was a shame not to win Superpole when we all put so much effort in but the main thing is that we have a front row start for the races. We have a good set-up for raceday and I think we can make our tyres go race distance at a good pace. We did a good race run this afternoon so it’s all feeling very positive. We have made real improvements in the bike since our last test.” Noriyuki Haga (12th – 1’59.571 – Yamaha Motor Italia WSB Team) “We have had a bit of a problem finding a good set up in some areas, but we have improved there, only to find a few smaller problems in another area. We have improved the feeling and tomorrow we can try another setting in a good direction, and we will see how things are after warm-up. We have already decided on a tyre for the race tomorrow, and I think we can find a better race pace than we can do in one single lap of qualifying, which is really important.” Massimo Meregalli (Team Manager, Yamaha Motor Italia WSB Team) “Everything is working well for Troy and he is happy about the bike and tyres. He made a great Superpole lap, he was so close to adding to his record total. Tomorrow we will try something different on Nori’s side. He has a good record here, so tomorrow I am sure we can find something better for him in warm-up anyway. In the end Nori is a racer on Sunday no matter what set-up he has so I am sure he can do well. Shinichi Nakatomi (18th – 2:00.232 – Team YZF Yamaha) “We changed the machine set up and made some progress but other teams also improved their times. The feeling ended up not so bad even if the grid position was not so good. The times are very close and after final qualifying we made good work to prepare for the race.” More, from a press release issued by Xerox Ducati: BAYLISS ON POLE, FABRIZIO THIRD AND CANEPA SIXTH ON THE GRID FOR TOMORROW’S RACES AT BRNO Brno (Czech Republic) Saturday 19th July: The second qualifying session of the weekend, held this morning, saw all three Ducati Xerox riders improve on the times they set yesterday, to qualify for Superpole in third (Bayliss), seventh (Fabrizio) and eighth place (Canepa). Superpole was action packed from the offset, with an immediate flying lap by Kiyonari, the first rider out, which really set the pace, as the next seven riders to exit were unable to beat his fast time. Niccolo’ Canepa, participating in his very first Superpole here this afternoon, was the first of the three Ducati Xerox riders to go out and completed a near perfect lap to take eventual sixth place on tomorrow’s grid. Michel Fabrizio followed him out, beating the times set by the entire field up until that point. The final group of three riders included Troy Bayliss who really made his Superpole lap count to take pole position for the fourth time this season. Troy Bayliss 1m58.3s “Brno has always been something of a bogey track for me but I hope that this weekend we are finally turning that around. The new surface of the track has really improved the grip which is great news. This morning went well and then in Superpole this afternoon, when I saw Corser’s time, I knew I was going to have to put in a really fast lap to be able to beat it and I managed that, but then Max (Biaggi) went out and I was worried he might in turn beat me. I hope tomorrow stays dry and then we’ll see but I have to say it would be pretty special to have a win here this time around.” Michel Fabrizio 1m58.8s “It’s a circuit that I really like and so I’m happy to get a place on the first row here. We have to see tomorrow whether I can make the good start that I need to really be in the running. We did a long-run this morning and it seemed to go ok but it’s obviously going to be hard tomorrow and I’ll no doubt have to fight once again against the two Troys and Biaggi!” Niccolo’ Canepa 1m59.3s “As it’s the first time that I’ve ever taken part in Superpole I have to say I’m really pleased with my performance. During my Superpole lap I made a small mistake and if it weren’t for that I’d have been a couple of tenths faster I think but I can’t complain with a place on the second row for tomorrow’s race. We’re still planning to make a few more little changes this evening to try during the morning’s warm-up as we could still improve our race pace but for now, I’m more than happy.” More, from a press release issued by Team Alstare Suzuki: SECOND AND THIRD ROWS FOR THE SUZUKI TRIO IN BRNO Team Suzuki Alstare rider Fonsi Nieto finished seventh quickest in Superpole and will start tomorrow’s pair of 20-lap races from the second row of the grid. His team mate Yukio Kagayama will be just behind on row three, with Alstare Suzuki rider Max Neukirchner alongside him. Ducatis dominated the front row of the grid, with Troy Bayliss taking his fourth Superpole of the year. His fellow countryman Troy Corser (Yamaha) is second, with Michel Fabrizio (Ducati) third and Max Biaggi (Ducati) fourth. Fonsi – 7th, 1:59.360 I am happy because today I found a good rhythm over a lot of laps on race tyres and was still going consistently fast at the end of eighteen laps. I made a little mistake in Superpole in the last sector, but the second row of the grid is OK here. So far the weekend has been going well. I am happy with the bike and I don’t think we’ll make any changes in the warm-up tomorrow morning. Every time we go out, the grip improves and I think there will be even more grip tomorrow. Whatever happens, I am going for the podium in both races. Max – 9th, 1:59.497 My Superpole lap was bit funny because I didn’t make any mistakes, felt good on the bike but the time was not good! It was strange because I had a feeling like that in the free practice this afternoon when I was on race tyres. For me the grip was better in the morning than the afternoon when I had a bit of a front end chatter. The third row of the grid is not so good, but the first corner is quite far from start so as long as I can get off the line quickly, I have a chance to be in the lead group straightaway. If I can make two good starts, there is no reason why I cannot get on the podium. Yukio – 10th, 1:59.537 I am not so happy to be on the third row of the grid, but I think that is because my Superpole lap was not so good. I made a little mistake in sector two, lost some time and that was that. I got into a turn a bit too hot, braked a bit too hard and then lost my drive exiting the corner. My biggest problem at the moment is getting the best settings for the electronics. When you have good settings, you can push very hard, but we have not yet found the ideal solution. We will try some changes in the warm-up tomorrow morning and see if we can find the best compromise for this track. Final qualifying 1 Bayliss (Aus-Ducati) 1:58.345, 2 Corser (Aus-Yamaha) 1:58.451, 3 Fabrizio (I-Ducati) 1:58.853, 4 Biaggi (I-Ducati) 1:59.069, 5 Kiyonari (J-Honda) 1:59.318, 6 Canepa (I-Ducati) 1:59.324, 7 Fonsi Nieto (E-Suzuki Alstare) 1:59.360, 8 Smrz (CZ-Ducati) 1:59.451, 8 Max Neukirchner (D-Alstare Suzuki) 1:59.497, 10 Yukio Kagayama (J-Suzuki Alstare) 1:59.537, FRONT ROW FOR XAVI. Team Alstare Suzuki rider Xavi Simeon posted the fourth quickest time in qualifying and will start tomorrow’s sixth round of this year’s Superstock 1000 FIM Cup on the front row of the grid. Aussie Brendan Roberts (Ducati) took pole position this afternoon, with Michele Pirro (Yamaha) second and Maxime Berger (Honda) third. Xavi – 4th, 2:04.150 I am happy to be on the front row and happy because the bike is working well and feels good to ride. I didn’t have any big problems today, just a small problem with the front tyre feel. But apart from that, nothing of note. I am looking forward to the race tomorrow and I think I can make the podium for sure. I hope to get a good start, fight at the front of the pack and be in a good position at the end. The important thing for me is to make sure I score a good number of points and maintain my championship lead. Final qualifying 1 Roberts (Aus-Ducati) 2:03.685, 2 Pirro (I-Yamaha) 2:03.924, 3 Berger (F-Honda) 2:03.929, 4 Xavi Simeon (B-Alstare Suzuki) 2:04.150, 5 Corti (I-Yamaha) 2:04.156, 6 Antonelli (I-Honda) 2:04.601, More, from a press release issued by HANNspree Ten Kate Honda: Kiyonari shines in Superpole qualifying Ryuichi Kiyonari was the HANNspree Ten Kate Honda Superbike team’s highlight of the day and set a blistering performance in the Superpole Qualifying this afternoon. He impressively worked his way forward after concluding the morning’s second qualifying session in sixteenth place. In what was easily his best qualifying performance to date, Kiyonari was the first man to start the one-lap race against the clock and pushed hard on his Honda CBR1000RR to set the time to be beaten at 1’59.318. It took seven riders before the time was crushed, firstly by Michel Fabrizio, then followed by Troy Corser and eventual pole-sitter Troy Bayliss. It was Max Biaggi who robbed Kiyonari of his first ever WSB front row start. A satisfied Kiyonari will now start tomorrow’s race from fifth place on the grid, his best position so far this season. Carlos Checa took a total reversal of fortune. After concluding the morning’s second qualifying practice in ninth position he didn’t succeed to improve in his Superpole lap and was eventually sent back to a fourth row start. Kenan Sofuoglu finished the second qualifying practice in a disappointing twenty-sixth position and did not qualify for Superpole. Carlos Checa, 1’59.587; “Today has been a poor day of qualifying for me. We are not far off the pace and have been able to stay consistent but I couldn’t set that single fast lap.” “My Superpole lap was far from good, I experienced a lot of rear chatter and lost valuable time. I will need a good start tomorrow and work towards a good position in the first laps and start the race from that point. It is a handicap having to start from the fourth row on the grid and not a position to win the race.” Ryuichi Kiyonari, 1’59.318; “I am very happy with my Superpole lap. I qualified sixteenth and made my way up to fifth place on the grid. That’s a big jump as I’m normally not strong in the one lap attack.” “My feeling with the machine and the tyres was good today on my best lap. We tried a different setting today and the feeling was improving throughout the sessions The pace is good but still not fast enough. I’ll try and make a good start tomorrow and then find the connection with the fast group and work from there. I’ll need to push hard in the first laps for a good result.” Kenan Sofuoglu, 2’01.302 (QP2); “It was quite a disappointing session for me today as we were expecting an improvement but it just didn’t work. I tried to watch other riders on their laps but just can’t seem to adapt to riding the big Superbike.” “The team have worked very hard but it hasn’t paid off so far and we are now past the mid-season mark. I hope we can make some improvement tomorrow to give some motivation to everybody in the team. Like every Saturday night I’m hoping for a better result on Sunday.” More, from a press release issued by Troy Corser’s publicist: TROY MISSES SUPERPOLE VICTORY BY A WHISKER! Troy missed his chance of notching up Superpole victory number forty-three by the narrowest of margins in Brno this afternoon. At the end, fellow countryman Troy Bayliss (Ducati) took Superpole, with a lap of 1:58.345 – a tenth of a second quicker. Apart from Troy’s Yamaha, the front row of the grid is an all Ducati affair, with Michel Fabrizio third and Max Biaggi fourth. Troy – 2nd, 1:58.451 I am pretty happy with how the weekend has gone so far and happy to be mixing it with all those Ducatis. I think the last three of four races have been good for us and the bike is working very well. The grip here has been improving throughout the weekend and I think it’s going to be as good, if not better, tomorrow. I had a bit of an unfortunate crash this morning and hurt my right shoulder a bit. It’s a bit sore, but it isn’t a problem when I’m on the bike and I don’t expect it to hold me back tomorrow. We had changed the front end geometry a bit to get more stability and to allow me to brake harder. After one lap, I tried to brake a bit later in one corner and down I went. I tumbled into the gravel trap and got hit by my bike and that’s what made my shoulder sore. I guess I was lucky that I didn’t hurt myself badly. But, we learnt something from the experience and that’s good. I feel we have quite a good set-up for the race and the tyres are consistent. I hope the weather stays dry and we can put on a good show for the fans. More, from a press release issued by Team Pedercini: Team Pedercini enters the Superpole for its forth time in this season. Aytron Badovini succeeded to be in the top sixteen, getting the possibility to run the quick lap. Today’s result satisfies both the team and the riders who is going to start from the 4th line hunting for points in tomorrow’s race. Same goal for Vittorio Iannuzzo who is improving round by round recovering from the bad injury of the season begin. The rider from Campania reached a good pace which allows him to feel confident about getting his first seasonal points tomorrow. On the other hand, the young riders of the Supertsock ran up against an harder qualifying. Yoann Tiberio is going to start from the sixth line while Alessio Aldrovandi from the seventh one. Both the riders are going to spend the warm-up fine-tuning the bike, testing a different balance in order to reverse the bad trend. VITTORIO IANNUZZO | Kawasaki ZX-10R | 25th classified in 2’01.214: “I have improved respect to Misano although I still cannot do my best when I need to push by using the soft tyre. That influences my starting position which I wished to be better especially with a view to the race. Anyway my pace is pretty good and passing is not impossible on this track so my goal is always the same: finishing the race in the top-15″. AYRTON BADOVINI | Kawasaki ZX-10R |16th classified in 2’01.161: “I’m pretty satisfied with running the Superpole once again and above all to be in a good form for tomorrow’s race which I hope to finish in the points. We have found a good setting which allows me to ride effectively without damaging the tyres too much, that might be crucial in the second part of the race”.

Updated: Parkes On World Supersport Pole Position In The Czech Republic

FIM Supersport World Championship Brno, Czech Republic July 19, 2008 Final Qualifying Results (all on Pirelli tires): 1. Broc PARKES (Yamaha YZF-R6) 2:03.203 2. Barry VENEMAN (Suzuki GSX-R600), 2:03.452 3. Josh BROOKES (Honda CBR600RR), 2:03.562 4. Andrew PITT (Honda CBR600RR), 2:03.590 5. Craig JONES (Honda CBR600RR), 2:03.761 6. Mark AITCHISON (Triumph Daytona 675), 2:03.775 7. Jonathan REA (Honda CBR600RR), 2:03.934 8. Vesa KALLIO (Honda CBR600RR), 2:04.135 9. Matthieu LAGRIVE (Honda CBR600RR), 2:04.368 10. Russel HOLLAND (Honda CBR600RR), 2:04.508 11. Gianluca NANNELLI (Honda CBR600RR), 2:04.546 12. Didier VAN KEYMEULEN (Suzuki GSX-R600), 2:04.605 13. Gregory LEBLANC (Honda CBR600RR), 2:04.670 14. Robbin HARMS (Honda CBR600RR), 2:04.676 15. Garry MCCOY (Triumph Daytona 675), 2:04.721 16. David SALOM (Yamaha YZF-R6), 2:04.779 17. Joan LASCORZ (Honda CBR600RR), 2:04.887 18. Massimo ROCCOLI (Yamaha YZF-R6), 2:04.891 19. Ivan CLEMENTI (Triumph Daytona 675), 2:04.903 20. Gianluca VIZZIELLO (Honda CBR600RR), 2:04.910 21. Chris WALKER (Kawasaki ZX-6R), 2:05.115 22. Fabien FORET (Yamaha YZF-R6), 2:05.151 23. Katsuaki FUJIWARA (Kawasaki ZX-6R), 2:05.328 24. Danilo DELL’OMO (Honda CBR600RR), 2:05.507 25. Graeme GOWLAND (Honda CBR600RR), 2:05.775 More, from a press release issued by Triumph Italia Be1 Racing: Triumph Italia Be1 Racing comes really close to the first row with Mark Aitchison. The young Aussie records the sixth best time after the second timed session at Brno, just one tenth slower than the former champion Andrew Pitt and his factory Honda. Aitchison has been really quick during the whole session, lapping several times close to his best time; that allows the rider and the team to feel confident for tomorrow’s race with the goal to improve the sixth final place taken fifteen days ago at Misano. On the other hand, Ivan Clementi is going to start form the fifth line. The Italian rider was not able to fix the rear chattering of his bike and that prevented him from getting a better result on a track which usually suits his riding style. MARK AITCHISON | Triumph 675 | 6th best time in 2’03.775: “I would have had the chance to start from the first line but I paid for my lack of experience and I was not able to improve my time further. We found a good setting this morning, then we focused on choosing the best kind of tyres for the race. I recorded my best time during a series of very quick laps; that is really good and I feel confident to be one of the best riders of tomorrow’s race”. IVAN CLEMENTI | Triumph 675 | 19th best time in 2’04.903: “My problem is linked with just two corners where I collect the most of the gap from the bests. I cannot find the right set-up for the fork in order to remove the chattering. Tomorrow morning we will test a different balancing for the bike in order to get a better control which can lead to improve my times”. More, from a press release issued by HANNspree Ten Kate Honda: Pitt starts Brno Supersport race from front row HANNspree Ten Kate Honda rider Andrew Pitt secured a front row start in the second day of qualifying in Brno. Pitt set the fastest time in his first lap of the afternoon’s official practice and looked likely to claim his third pole of the season. He focused for the remainder of the session on finding the right tyres and didn’t manage to further improve his fastest time of 2’03.590 0.387s behind pole sitter Broc Parkes. Pitt, who is looking for a continuation of his winning streak, will start Sunday’s race from fourth place on the grid. Jonathan Rea has adapted himself quickly to the new track and topped the time sheets in the morning’s free practice session. In the official practice Rea maintained his pace and secured a second row start in a best time of 2’03.934, the seventh fastest qualifying time. Both riders are confident with their race pace and set-up and aim to convert their starting positions into a top finish for the team. Andrew Pitt, 2’03.590; “I am pretty happy to be on the front row. We probably had pole there for a while and luckily we stayed on the front row. We wanted to come through on the tyre choice and stayed out there and didn’t come back in to put new tyres in again.” “We found the best combination with the tyres and Johnny and I are in a good position to be really strong in the race. I’m looking forward to racing tomorrow.” Jonathan Rea, 2’03.934; “For me the qualifying sessions today were ok. I looked at the race pace of the other riders and we are right in the ball park. I put some race laps together in the session and concentrated on the race set-up.” “We have a good set-up for tomorrow and I’m confident with my tyre choice. I am really looking forward to the race, we have the pace to do well and I’m really confident. I just hope from row two I can make a good start and be there from lap one and challenge the fight for a race.” More, from a press release issued by Scuderia Triumph-SC: GARRY McCOY INJURED IN PRACTICE SESSION AT BRNO (Brno Czech Republic 2008, July 19) The main event of the second practice day at Brno Automotodrom for Triumph-SC Team has been the very bad accident occurred to Garry McCoy during the second free practice session in the morning. About ten minutes to the finish Garry, who was running very fast, so that at first split he recorded the fourth fastest, found on his line outing a corner in the downhill sector, the Pitt’s Honda running slowly along the track edge. McCoy, heavy engaged to grab a fast lap, tried to spare the unexpected obstacle, but he touched with the front brake lever to Honda’s back. The 675 Daytona of the veteran Aussie has been throw to the protections along the track. The crash has been very hard, the bike front has been disintegrated while Garry crashed against the wall with the left part of his back. Broken ribs and a heavy internal thoracic trauma. The rider was conscious, able to manage the action of first aid rescue along the track. After the first control by Clinica Mobile people McCoy has been translated by medical helicopter to Úrazová Nemocnice Hospital in Brno-Trnitá for more controls to verify the presence of injuries at lung and pleura level. The following controls did show also a fracture at the sixth loin vertebra, without any damage at neurological level, as well a left lung contusion, so Garry has been transported, following his request, to Private Klinik in Wien, where an orthopaedic specialist well known by Garry is working. Ruggero Scambia clearly increased his performance, as well the grid position did not change too much: “I increased more as 3 seconds my lap time, but that wasn’t enough and I remained in the back of the grid. But now the gap from most of my rivals is possible to manage and if I’ll have a good start I could look for a result able to give me trust for next events.” No glory in 600 Superstok race for Robbie Stewart, 25th at the finish after a bad start that put him il the last position at the end of the first lap: “I don’t know how to say, the bike runs well, but i had a slow start and then I was not able to have a good pace. Just in the final laps I started to ride better, but it was too late.” More, from a press release issued by Yamaha Racing: Parkes takes fifth pole position in a row Broc Parkes consistently brilliant performances in qualifying in the 2008 season continued at the Brno meeting when he took a remarkable fifth consecutive pole position. His pre-race successes at Assen, Monza, Nürburgring and Misano grew to five after Parkes scored a 2’03.203 second lap towards the end of a busy afternoon session. Parkes’ lap was a new absolute track best, on a circuit which had been resurfaced earlier in the season. The expected rains stayed away during the second day of track action, allowing Parkes to lead Barry Veneman, Josh Brookes and Andrew Pitt on the front row of the grid. Fabien Foret is recovering from a day one crash that saw him crack his C6 and C7 vertebrae, and suffer a concussion. Latest medical reports indicate that Foret will be out of action for two months, but should make a full recovery. Massimo Roccoli (Yamaha Team Italia Lorenzini by Leoni) slipped one place to 18th on the grid on day two of qualifying and David Salom (Yamaha Spain World Supersport) went 16th. Broc Parkes (1st – 2’03.203 – Yamaha World Supersport Team) “It’s a great feeling to have had five pole position rides in a row and I’m happy with the final results of all the work we did in qualifying. Our bike is working really well on fresh rubber, as usual. I think that the rate of wear from the tyres will be the same for everyone in the race tomorrow, and the pace will be pretty even between the top guys. Maybe it will be a case of managing the tyres in the last few laps. But on the new track surface, we’ll have to wait and see.” Wilco Zeelenberg (Team Manager, Yamaha World Supersport Team) “Broc is simply brilliant at getting pole positions and five in a row is really something special. What can we say, qualifying fastest is what he is really good at right now and the desire to succeed is also in his guts at the moment. He kept his patience to wait until we got to know all the information we needed for the race, even though another rider went faster near the end. Only then did Broc go out and take pole. That is the best thing about his practice performances, his willingness to work for a good race set-up.” Massimo Roccoli (18th – 2’04.891 seconds – Yamaha Team Italia Lorenzini by Leoni) “Today wasn’t a good day because although the bike was very good, the engine has had another step of evolution and was very competitive, I didn’t ride as aggressively as I needed to. Our tyre strategy was excellent but I think it is simply a problem of my confidence to go as fast as I know I can.” David Salom: (16th – 2’04.779 seconds – Yamaha Spain) “I’ve been riding very comfortably and the faster I went the more comfortable I felt. My best lap time is very good, faster than last year’s pole position. I’ve improved my best time from last year by three seconds and the bike, team and me have all improved too.”

Biaggi Tops Second World Superbike Qualifying Session At Brno

FIM Superbike World Championship Brno, Czech Republic July 19, 2008 Qualifying Results (before Superpole, all on Pirelli tires): 1. Max BIAGGI (Ducati 1098 RS08), 1:58.965 2. Jakub SMRZ (Ducati 1098 RS08), 1:59.125 3. Troy BAYLISS (Ducati 1098 F08), 1:59.166 4. Max NEUKIRCHNER (Suzuki GSX-R1000), 1:59.250 5. Fonsi NIETO (Suzuki GSX-R1000), 1:59.357 6. Troy CORSER (Yamaha YZF-R1), 1:59.380 7. Michel FABRIZIO (Ducati 1098 F08), 1:59.482 8. Niccolo CANEPA (Ducati 1098 F08), 1:59.634 9. Carlos CHECA (Honda CBR1000RR), 1:59.648 10. Yukio KAGAYAMA (Suzuki GSX-R1000), 1:59.708 11. Ruben XAUS (Ducati 1098 RS08), 1:59.846 12. Lorenzo LANZI (Ducati 1098 RS08), 1:59.850 13. Noriyuki HAGA (Yamaha YZF-R1), 1:59.913 14. Karl MUGGERIDGE (Honda CBR1000RR), 1:59.944 15. Ayrton BADOVINI (Kawasaki ZX-10R), 2:00.221 16. Ryuichi KIYONARI (Honda CBR1000RR), 2:00.225 17. David CHECA (Yamaha YZF-R1), 2:00.228 18. Shinichi NAKATOMI (Yamaha YZF-R1), 2:00.232 19. Gregorio LAVILLA (Honda CBR1000RR), 2:00.304 20. Roberto ROLFO (Honda CBR1000RR), 2:00.374 21. Regis LACONI (Kawasaki ZX-10R), 2:00.482 22. Makoto TAMADA (Kawasaki ZX-10R), 2:00.641 23. Shuhei AOYAMA (Honda CBR1000RR), 2:00.905 24. Sebastien GIMBERT (Yamaha YZF-R1), 2:01.059 25. Vittorio IANNUZZO (Kawasaki ZX-10R), 2:01.214 26. Kenan SOFUOGLU (Honda CBR1000RR), 2:01.302 27. Jiri DRASDAK (Honda CBR1000RR), 2:02.373 28. Christian ZAISER (Yamaha YZF-R1), 2:03.118 29. Jason PRIDMORE (Honda CBR1000RR), 2:03.397 30. Milos CIHAK (Suzuki GSX-R1000), 2:03.758